2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

TERMINALS OF ECU

System information · Vehicles built Sep 2011 – Dec 2011


PARKING ASSIST ECU
E132051E11
  1. Disconnect the F43 connector from the ECU.

  2. Measure the voltage and resistance of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F43-6 (+B) - F43-4 (GND1)
    L - W-B
    Power source signal
    Always
    11 to 14 V
    F43-4 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F43-1 (IG) - F43-4 (GND1)
    G - W-B
    IG power source signal
    Engine switch on (IG)
    11 to 14 V
    F43-14 (ACC) - F43-4 (GND1)
    GR - W-B
    ACC power source signal
    Engine switch on (ACC)
    11 to 14 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the F43 connector to the ECU.

  4. Measure the voltage and check for pulses according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F43-10 (CANL) - F43-4 (GND1)
    L - W-B
    CAN communication signal
    CAN communication circuit
    Pulse generation
    F43-9 (CANH) - F43-4 (GND1)
    V - W-B
    CAN communication signal
    CAN communication circuit
    Pulse generation
    F43-32 (TX-) - F43-31 (TX+)
    L - W
    AVC-LAN communication signal
    -
    -
    F44-34 (CV-) - F43-4 (GND1)
    W - W-B
    Rear television camera ground
    Always
    Below 1 V
    F44-10 (CV+) - F43-4 (GND1)
    R - W-B
    Rear television camera display signal (NTSC) input
    Engine switch on (IG)
    Shift lever in R
    Under normal conditions
    Pulse generation
    (See waveform 1)
    Engine switch on (IG)
    Shift lever in R
    Camera lens is covered, blacking out screen
    Pulse generation
    (See waveform 2)
    F44-11 (CGND) - F43-4 (GND1)
    Shield - W-B
    Rear television camera ground (shield)
    Always
    Below 1 V
    F44-35 (CB+) - F43-4 (GND1)
    B - W-B
    Power source to rear television camera
    Engine switch on (IG)
    Shift lever in R
    5.8 to 7.0 V
    If the result is not as specified, the ECU may have a malfunction.

  5. E171712E01
    Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


    1. Waveform 1 (under normal conditions)

      Item
      Content
      Terminal No. (Symbol)
      F44-10 (CV+) - F43-4 (GND1)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Engine switch on (IG), shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)

      Item
      Content
      Terminal No. (Symbol)
      F44-10 (CV+) - F43-4 (GND1)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Engine switch on (IG), shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *1
      Waveform 1 (under normal conditions)
      *2
      Waveform 2 (camera lens is covered, blacking out the screen)
      *3
      Synchronized Signal
      *4
      Video Waveform


REAR TELEVISION CAMERA ASSEMBLY

  1. Disconnect the S5 connector from the rear television camera assembly.
    E150739E13

  2. Measure the voltage of each terminal of the wire harness side connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S5-4 (CB+) - Body ground
    B - Body ground
    Power source
    Engine switch on (IG)
    Shift lever in R
    5.8 to 7.0 V
    If the result is not as specified, there may be a malfunction on the wire harness side.

  3. Reconnect the S5 connector to the rear television camera assembly.

  4. Check for pulses between each terminal of the connector.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S5-2 (CV+) - S5-1 (CV-)
    R - W
    Display signal
    Engine switch on (IG)
    Shift lever in R
    Under normal conditions
    Pulse generation
    (See waveform 1)
    Engine switch on (IG)
    Shift lever in R
    Camera lens covered, blacking out screen
    Pulse generation
    (See waveform 2)

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.

    If the result is not as specified, the camera may have a malfunction.

  5. E171712E01
    Reference (Oscilloscope waveform):

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.


    1. Waveform 1 (under normal conditions)

      Item
      Content
      Terminal No. (Symbol)
      S5-2 (CV+) - S5-1 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Engine switch on (IG), shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

    2. Waveform 2 (camera lens is covered, blacking out the screen)

      Item
      Content
      Terminal No. (Symbol)
      S5-2 (CV+) - S5-1 (CV-)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      Engine switch on (IG), shift lever in R

      HINT:
      The video waveform changes according to the image sent by the rear television camera assembly.

      Text in Illustration 
      *1
      Waveform 1 (under normal conditions)
      *2
      Waveform 2 (camera lens is covered, blacking out the screen)
      *3
      Synchronized Signal
      *4
      Video Waveform


DISPLAY AND NAVIGATION MODULE DISPLAY
  1. for HDD (Click here).
  2. for DVD (Click here).
← PROBLEM SYMPTOMS TABLE (Sep 2011 – Dec 2011)DIAGNOSIS SYSTEM (Sep 2011 – Dec 2011) →