2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

TERMINALS OF ECU

System information · Vehicles built from Jan 2012


PARKING ASSIST ECU
E245334E10
  1. Disconnect the F75 and F76 parking assist ECU connectors.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F75-1 (+B) - F75-4 (GND1)
    L - W-B
    Power source signal
    Always
    11 to 14 V
    F75-4 (GND1) - Body ground
    W-B - Body ground
    Ground
    Always
    Below 1 Ω
    F75-8 (IG) - F75-4 (GND1)
    G - W-B
    IG power source signal
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V
    F75-9 (ACC) - F75-4 (GND1)
    GR - W-B
    ACC power source signal
    Engine switch on (ACC)
    11 to 14 V
    Engine switch off
    Below 1 V
    F76-7 (BLSW) - F75-4 (GND1)
    G - W-B
    Front and side monitor main switch power source signal
    Engine switch on (IG), front and side monitor main switch on
    11 to 14 V

  3. Reconnect the F75 and F76 parking assist ECU connectors.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    F75-10 (TX-)
    L
    AVC-LAN communication signal
    -
    -
    F75-11 (TX+)
    W
    AVC-LAN communication signal
    -
    -
    F76-38 (CV-) - F75-37 (CGND)
    W - Shielded
    Rear television camera ground
    Always
    Below 1 V
    F76-15 (CV+) - F75-37 (CGND)
    R - Shielded
    Rear television camera display signal (NTSC) input
    Engine switch on (IG), shift lever in R
    Pulse generation (See waveform)
    F76-37 (CGND) - F75-4 (GND1)
    Shielded - W-B
    Rear television camera ground (shield)
    Always
    Below 1 V
    F76-14 (CB+) - F75-37 (CGND)
    B - Shielded
    Power source to rear television camera
    Engine switch on (IG), shift lever in R
    5.5 to 7.05 V

  5. E171712E22
    Using an oscilloscope, check waveform.
    Text in Illustration 
    *a
    Waveform A (camera lens not covered, displaying an image)
    *b
    Waveform B (camera lens covered, blacking out the screen)
    *c
    Synchronized Signal
    *d
    Video Waveform

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.


    1. Waveform

      Item
      Content
      Terminal No. (Symbol)
      F76-15 (CV+) - F75-37 (CGND)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      1. Waveform A: Engine switch on (IG), shift lever in R and camera lens is not covered, displaying an image.
      2. Waveform B: Engine switch on (IG), shift lever in R and camera lens is covered, blacking out the screen.


REAR TELEVISION CAMERA ASSEMBLY
E115535E11
  1. Disconnect the S5 rear television camera assembly connector.

  2. Measure the voltage and resistance according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S5-3 (CGND) - Body ground
    BR - Body ground
    Ground
    Always
    Below 1 Ω
    S5-4 (CB+) - S5-3 (CGND)
    B - BR
    Power source
    Engine switch on (IG), shift lever in R
    5.5 to 7.05 V

  3. Reconnect the S5 rear television camera assembly connector.

    HINT:
    A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected. If the result is not as specified, the rear television camera assembly may have a malfunction.

  4. Measure the voltage according to the value(s) in the table below.

    Terminal No. (Symbol)
    Wiring Color
    Terminal Description
    Condition
    Specified Condition
    S5-2 (CV+) - S5-3 (CGND)
    R - BR
    Display signal
    Engine switch on (IG), shift lever in R
    Pulse generation (See waveform)
    S5-1 (CV-) - S5-3 (CGND)
    W - BR
    Rear television camera ground
    Always
    Below 1 V

  5. E171712E22
    Using an oscilloscope, check waveform.
    Text in Illustration 
    *a
    Waveform A (camera lens not covered, displaying an image)
    *b
    Waveform B (camera lens covered, blacking out the screen)
    *c
    Synchronized Signal
    *d
    Video Waveform

    HINT:
    The video waveform changes according to the image sent by the rear television camera assembly.


    1. Waveform

      Item
      Content
      Terminal No. (Symbol)
      S5-2 (CV+) - S5-3 (CGND)
      Tool Setting
      200 mV/DIV., 50 μsec./DIV.
      Condition
      1. Waveform A: Engine switch on (IG), shift lever in R and camera lens is not covered, displaying an image.
      2. Waveform B: Engine switch on (IG), shift lever in R and camera lens is covered, blacking out the screen.


MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)

MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) [w/o Power Back Door System] (Click here)

POWER BACK DOOR UNIT ASSEMBLY [w/ Power Back Door System] (Click here)
← PROBLEM SYMPTOMS TABLE (from Jan 2012)DIAGNOSIS SYSTEM (from Jan 2012) →