C1622 Back Camera Disconnected
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
This DTC is stored if the multi-media module receiver assembly judges that the signals or signal lines between the multi-media module receiver assembly and the rear television camera assembly are not normal as a result of its self check.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1622 |
Open or short in the rear television camera assembly signal circuit |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When "System initializing" is displayed on the multi-media module receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system (w/o Side Monitor System) may be needed (Click here).
- When "System initializing" is displayed on the multi-media module receiver assembly after disconnecting the cable from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
| 1. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER - REAR TELEVISION CAMERA AND BODY GROUND) |
Disconnect the F77 multi-media module receiver assembly connector.
Disconnect the S5 rear television camera assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F77-18 (V+) - S5-2 (CV+)
Always
Below 1 Ω
F77-19 (V-) - S5-1 (CV-)
Always
Below 1 Ω
F77-39 (CA+) - S5-4 (CB+)
Always
Below 1 Ω
F77-40 (CGND) - S5-3 (CGND)
Always
Below 1 Ω
F77-12 (GND1) - Body ground
Always
Below 1 Ω
F77-18 (V+) - Body ground
Always
10 kΩ or higher
F77-19 (V-) - Body ground
Always
10 kΩ or higher
F77-39 (CA+) - Body ground
Always
10 kΩ or higher
F77-40 (CGND) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CA+, CGND) |
Reconnect the multi-media module receiver assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F77-40 (CGND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
F77-39 (CA+) - F77-40 (CGND)
Engine switch on (IG), shift lever in R
5.5 to 7.05 V
Text in Illustration *a
Component with harness connected
(Multi-media Module Receiver Assembly)
|
|
||||
| OK | |
| 3. CHECK REAR TELEVISION CAMERA ASSEMBLY (CV+, CGND) |
Reconnect the S5 rear television camera assembly connector.


| *a |
Component with harness connected (Multi-media Module Receiver Assembly) |
*b |
Waveform A |
| *c |
Waveform A |
*d |
Synchronization Signal |
| *e |
Video Waveform |
- |
- |
Check the waveform of the rear television camera assembly using an oscilloscope.
- HINT:
- A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.
- The video waveform changes according to the image sent by the rear television camera assembly.
- A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the multi-media module receiver assembly with the connector connected.
Measurement Condition Item
Content
Tester No. (Symbol)
F77-18 (V+) - F77-40 (CGND)
Tool Setting
0.2 V/DIV., 50 μS/DIV
Condition
Waveform A: Engine starts, shift lever in R (camera lens is not covered, displaying an image)
Waveform B: Engine starts, shift lever in R (camera lens is covered, blacking out the screen)
- OK:
- Waveform is as shown in the illustration.
|
|
||||
| OK | ||
| ||
