2011-2013 Land Cruiser · Service Manual Vehicle Interior

Security Horn Circuit

Circuit diagnosis · Vehicles built from Sep 2011

DESCRIPTION

When the theft deterrent system is switched from the armed state to the alarm sounding state, the main body ECU (cowl side junction block assembly LH) transmits a signal to cause the security horn to sound at intervals of 0.4 seconds.

WIRING DIAGRAM

B184350E09

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Body / Main Body / Active Test.

  1. According to the display on the intelligent tester, perform the Active Test.

    Main Body 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Security Horn
    Security horn
    ON / OFF
    -

OK:
The security horn assembly sounds and stops correctly when operated through the intelligent tester.



NG
Go to step 2
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK ASSEMBLY LH)

2. INSPECT SECURITY HORN ASSEMBLY

  1. E140469E01
    Remove the security horn assembly (Click here).

  1. Check the operation of the security horn assembly.

    Standard:
    Measurement Condition
    Specified Condition
    Battery positive (+) → Terminal 1
    Horn sounds
    Battery negative (-) → Horn body



NG
REPLACE SECURITY HORN ASSEMBLY (Click here)
OK


3. INSPECT SECURITY HORN RELAY

  1. E145692E12
    Remove the SECURITY HORN relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Specified Condition
    3 - 5
    10 kΩ or higher
    (when battery voltage is not applied between terminals 1 and 2)
    3 - 5
    Below 1 Ω
    (when battery voltage is applied between terminals 1 and 2)

    Text in Illustration 
    *a
    SECURITY HORN Relay



NG
REPLACE SECURITY HORN RELAY
OK


4. CHECK HARNESS AND CONNECTOR (BATTERY - SECURITY HORN RELAY)

  1. B292777E01
    Remove the SECURITY HORN relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block and junction block assembly SECURITY HORN relay terminal 2- Body ground
    Always
    11 to 14 V
    Engine room relay block and junction block assembly SECURITY HORN relay terminal 5 - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *a
    Engine Room Relay Block
    *b
    SECURITY HORN Relay



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - SECURITY HORN ASSEMBLY)
  1. Remove the SECURITY HORN relay from the engine room relay block.

  1. Disconnect the A19 security horn assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block and junction block assembly SECURITY HORN relay terminal 3 - A19-1
    Always
    Below 1 Ω
    Engine room relay block and junction block assembly SECURITY HORN relay terminal 3 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK HARNESS AND CONNECTOR (SECURITY HORN RELAY - MAIN BODY ECU)
  1. Remove the SECURITY HORN relay from the engine room relay block.

  1. Disconnect the E4 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    Engine room relay block and junction block assembly SECURITY HORN relay terminal 2 - E4-6 (SH)
    Always
    Below 1 Ω
    Engine room relay block and junction block assembly SECURITY HORN relay terminal 2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK ASSEMBLY LH)


← Engine Hood Courtesy Switch Circuit (from Sep 2011)Security Indicator Light Circuit (Sep 2011 – Dec 2011) →