B1676/85 Lost Communication with Rear Floor Airbag Sensor RH
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- B1677/85 Rear Floor Airbag Sensor RH Initialization Incomplete
- B1694/85 Side Satellite Sensor No. 2 Bus RH Initialization Incomplete
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
- HINT:
- "Rear floor airbag sensor RH" refer to the rear floor airbag sensor.
- The rear floor airbag sensor circuit consists of the center airbag sensor and rear floor airbag sensor.
The rear floor airbag sensor detects impacts to the vehicle and sends signals to the center airbag sensor to determine if the airbag should be deployed.
DTC B1676/85, B1677/85 or B1694/85 is stored when a malfunction is detected in the rear floor airbag sensor circuit.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B1676/85 |
When one of the following conditions is met:
|
|
| B1677/85 |
When one of the following conditions is met:
|
|
| B1694/85 |
When one of the following conditions is met:
|
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When disconnecting the cable from the negative (-) battery terminal while performing repairs, some systems need to be initialized after the cable is reconnected (Click here).
| 1. CHECK CONNECTION OF CONNECTORS |
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Check that the connectors are properly connected to the center airbag sensor and the rear floor airbag sensor.
- OK:
- The connectors are properly connected.
|
|
||||
| OK | |
| 2. CHECK CONNECTORS |
Disconnect the connectors from the center airbag sensor and rear floor airbag sensor.
Check that the connectors (on the center airbag sensor side and rear floor airbag sensor side) are not damaged.
- OK:
- The connectors are not deformed or damaged.
|
|
||||
| OK | |
| 3. CHECK REAR FLOOR AIRBAG SENSOR CIRCUIT |
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.


Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
L19-2 (BER+) - Body ground
Ignition switch ON
Below 1 V
L19-1 (BER-) - Body ground
Ignition switch ON
Below 1 V
Turn the ignition switch off.
Disconnect the cable from the negative (-) battery terminal, and wait for at least 90 seconds.
Using a service wire, connect terminals 20 (BCR+) and 19 (BCR-) of connector B.
- NOTICE:
- Do not forcibly insert the service wire into the terminals of the connector when connecting a service wire.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L19-2 (BER+) - L19-1 (BER-)
Always
Below 1 Ω
Disconnect the service wire from connector B.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
L19-2 (BER+) - L19-1 (BER-)
Always
1 MΩ or higher
L19-2 (BER+) - Body ground
Always
1 MΩ or higher
L19-1 (BER-) - Body ground
Always
1 MΩ or higher
|
|
||||
| OK | |
| 4. CHECK REAR FLOOR AIRBAG SENSOR |
Connect the connectors to the center airbag sensor.

Temporarily replace the rear floor airbag sensor with a new one.
Connect the cable to the negative (-) battery terminal, and wait for at least 2 seconds.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Clear the DTCs stored in the memory (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON, and wait for at least 60 seconds.
Check for DTCs (Click here).
- OK:
- DTC B1676, B1677 and B1694 are not output.
- HINT:
- Codes other than DTC B1676, B1677 and B1694 may be output at this time, but they are not related to this check.
|
|
||||
|
|
||||
| C | ||
| ||
