2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REASSEMBLY

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. A bolt without a torque specification is shown in the standard bolt chart (Click here).
  2. When installing the front bumper protector, heat the front bumper surface using a heat light.

    Standard Heating Temperature:
    Item
    Temperature
    Front Bumper
    20 to 30°C (68 to 86°F)

NOTICE:
Do not heat the front bumper excessively.


1. INSTALL WINCH CONTROL WIRE

  1. B180480
    Install the winch control wire with the 2 nuts.

    Torque:
    5 N*m{ 51 kgf*cm , 45 in.*lbf }


2. INSTALL FRONT LICENSE PLATE BRACKET

B185495
  1. Install the license plate bracket with the 2 nuts.


3. INSTALL FRONT NO. 2 BUMPER PROTECTOR
  1. Clean the front bumper surface.

    1. Using a heat light, heat the front bumper surface.

    2. Remove the double-sided tape from the front bumper.

    3. Wipe off any tape adhesive residue with cleaner.

  1. B185494
    Install a new bumper protector.

    1. Remove the peeling paper from the face of a new bumper protectors.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    2. Install the 2 bumper protectors as shown in the illustration.


4. INSTALL FRONT BUMPER PROTECTOR
  1. Clean the front bumper surface.

    1. Using a heat light, heat the front bumper surface.

    2. Remove the double-sided tape from the front bumper.

    3. Wipe off any tape adhesive residue with cleaner.

  1. B185493
    Install a new bumper protector.

    1. Remove the peeling paper from the face of a new bumper protectors.

      HINT:
      After removing the peeling paper, keep the exposed adhesive free from foreign matter.

    2. Install the 2 bumper protectors as shown in the illustration.


5. INSTALL LOWER RADIATOR GRILLE LH

B188081
  1. Attach the 7 claws to install the lower radiator grille.


6. INSTALL LOWER RADIATOR GRILLE RH

HINT:
Use the same procedures described for the LH side.


7. INSTALL FRONT BUMPER HOLE COVER LH (w/o Fog Light)

B181003
  1. Install the bumper hole cover with the 3 screws.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }


8. INSTALL FRONT BUMPER HOLE COVER RH (w/o Fog Light)

HINT:
Use the same procedures described for the LH side.


9. INSTALL FOG LIGHT ASSEMBLY LH (w/ Fog Light)

  1. E155839
    Install the fog light with the 3 bolts.

    Torque:
    5.0 N*m{ 51 kgf*cm , 44 in.*lbf }

  1. Attach the 2 clamps.


10. INSTALL FOG LIGHT ASSEMBLY RH (w/ Fog Light)

HINT:
Use the same procedures described for the LH side.


11. INSTALL NO. 1 ULTRASONIC SENSOR RETAINER (w/ TOYOTA Parking Assist-sensor System)

E156306E01

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor retainer on the other side.

  1. Align the keyhole and protrusion as shown in the illustration.

  1. Install the ultrasonic sensor retainer to the front bumper cover.

    NOTICE:
    Do not damage the bumper with the protrusion when installing the retainer.


12. INSTALL NO. 1 ULTRASONIC SENSOR (w/ TOYOTA Parking Assist-sensor System)

E146466

HINT:
Use the same procedure to install the No. 1 ultrasonic sensor on the other side.

  1. Attach the 2 claws to install the ultrasonic sensor.

  1. Connect the connector.


13. INSTALL NO. 4 ENGINE ROOM WIRE

  1. w/o TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 9 clamps to install the engine room wire.

    2. Connect the 2 connectors.

      B185489

  1. w/ TOYOTA Parking Assist-sensor System, w/ Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 9 clamps to install the engine room wire.

    2. Connect the 4 connectors.

      B185490

  1. w/ TOYOTA Parking Assist-sensor System, w/o Fog Light:
    Install the No. 4 engine room wire.

    1. Attach the 9 clamps to install the engine room wire.

    2. Connect the 2 connectors.

      B185491

← DISASSEMBLY (from Jan 2012)REASSEMBLY (from Jan 2012) →