2011-2013 Land Cruiser · Service Manual Vehicle Exterior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE REAR DOOR INSIDE HANDLE BEZEL LH

  1. B180907E01
    Using a screwdriver, detach the 4 claws and remove the rear door inside handle bezel LH.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


4. REMOVE REAR DOOR ARMREST BASE PANEL ASSEMBLY LH

  1. B180908
    Using a moulding remover, detach the 7 claws.

  1. Disconnect the connector and remove the armrest base panel.


5. REMOVE ASSIST GRIP COVER LH

  1. B180910
    Using a moulding remover, detach the 9 claws and remove the assist grip cover LH.


6. REMOVE REAR DOOR TRIM BOARD SUB-ASSEMBLY LH

  1. B310802E01
    Remove the 3 screws.

  1. Remove the 9 clips.

  1. Remove the rear inner door glass weatherstrip LH together with the rear door trim board sub-assembly LH by pulling them upward in the order shown in the illustration.

    HINT:
    Make sure that the pin labeled A in the illustration is detached from the door panel.

  1. Disconnect the connector and remove the rear door trim board sub-assembly LH.

  1. B180913
    Disconnect the 2 cables from the rear door inside handle sub-assembly LH.


7. REMOVE REAR INNER DOOR GLASS WEATHERSTRIP LH

  1. B310803
    Detach the 4 clips and remove the rear inner door glass weatherstrip LH from the rear door trim board sub-assembly LH.

    NOTICE:
    1. Squeeze the metal clip to remove it.
    2. The metal clip may be deformed if it is forcibly pulled.


8. REMOVE REAR DOOR SERVICE HOLE COVER LH

  1. B183933E01
    Using a clip remover, detach the 6 clamps.

  1. Remove the bolt and disconnect the 2 connectors.

  1. Remove the rear door service hole cover LH.

    HINT:
    Remove the remaining tape on the door.


9. REMOVE REAR DOOR GLASS RUN LH

  1. B180919
    Remove the rear door glass run LH from the window frame.


10. REMOVE REAR DOOR REAR LOWER WINDOW FRAME SUB-ASSEMBLY LH

  1. B180920
    Remove the 2 bolts.

  1. Remove the screw and rear door rear lower window frame sub-assembly LH.


11. REMOVE REAR DOOR QUARTER WINDOW GLASS LH

  1. B180923
    Remove the rear door quarter window glass LH and rear door quarter window weatherstrip LH as a unit as shown in the illustration.


12. REMOVE REAR DOOR GLASS SUB-ASSEMBLY LH

  1. B180921
    Remove the rear door glass sub-assembly LH from the rear door window regulator sub-assembly LH as shown in the illustration.

    NOTICE:
    Do not damage the door glass.


13. REMOVE REAR DOOR BELT MOULDING ASSEMBLY LH

B182607E01
  1. Put protective tape around the belt moulding.

  1. B182605
    Detach the claw and remove the belt moulding.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →