DISASSEMBLY
Removal / installation · Vehicles built from Sep 2011
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for RHD and LHD vehicles.
- The procedure listed below is for LHD vehicles.
- Use the same procedure for RHD and LHD vehicles.
| 1. REMOVE SEAT ADJUSTER COVER CAP RH |
![]() ![]() |
Remove the 2 seat adjuster cover caps.
| 2. REMOVE FRONT SEAT INNER BELT ASSEMBLY RH |
Remove the nut and front seat inner belt assembly RH.

| 3. REMOVE RECLINING ADJUSTER RELEASE HANDLE RH |
![]() ![]() |
Using a screwdriver, detach the claw and remove the reclining adjuster release handle RH.
Text in Illustration *1
Protective Tape
- HINT:
- Tape the screwdriver tip before use.
| 4. REMOVE FRONT SEAT CUSHION SHIELD RH |
Detach the 2 rubber bands.

Remove the 2 screws.

Detach the claw.
Detach the 2 guides and remove the front seat cushion shield RH.
| 5. REMOVE FRONT SEAT HINGE KNOB |
![]() ![]() |
Twist the front seat hinge knob in the direction indicated by the arrow and remove it.
| 6. REMOVE FRONT SEAT HINGE COVER RH |
![]() ![]() |
Remove the 2 screws.
Detach the 2 hooks and remove the front seat hinge cover RH.
| 7. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
![]() ![]() |
Remove the 2 screws.
Detach the hook and remove the front seat lower cushion shield RH.
| 8. REMOVE INNER SEAT BRACKET ASSEMBLY RH |
![]() ![]() |
Remove the 4 bolts and inner seat bracket assembly RH.
| 9. REMOVE SEAT ARMREST ASSEMBLY RH |
![]() ![]() |
Remove the bolt and seat armrest assembly RH.
| 10. REMOVE FRONT SEAT ARMREST HOLE BOARD COVER |
![]() ![]() |
Remove the front seat armrest hole board cover from the seat armrest assembly RH.
| 11. REMOVE FRONT SEATBACK SIDE COVER SUB-ASSEMBLY RH |
![]() ![]() |
Detach the fastening tape and open the front seatback side cover sub-assembly RH.
Remove the front seatback inside pad RH.

Remove the front seatback side cover sub-assembly RH.

| 12. REMOVE FRONT SEAT CUSHION EDGE PROTECTOR |
![]() ![]() |
Bend out the 2 cushion edge tabs.
Text in Illustration *1
Cushion Edge Tab
- NOTICE:
- Be careful not to break the cushion edge tabs.
Remove the 2 front seat cushion edge protectors.
| 13. REMOVE SEAT CUSHION COVER WITH PAD |
Remove the hog rings and detach the hooks.

Text in Illustration *1
Hog Ring
*2
Hook
Remove the hog ring and seat cushion cover with pad.
| 14. REMOVE SEPARATE TYPE FRONT SEAT CUSHION COVER |
Remove the hog rings and separate type front seat cushion cover from the separate type front seat cushion pad.

| 15. REMOVE CENTER SEAT HINGE COVER |
![]() ![]() |
Remove the screw and center seat hinge cover.
| 16. REMOVE FRONT SEAT INNER CUSHION SHIELD RH |
![]() ![]() |
Remove the screw and detach the claw.
Detach the clip and remove the front seat inner cushion shield RH.
| 17. REMOVE SEATBACK COVER WITH PAD |
Open the 2 fasteners and remove the hog rings.

Text in Illustration *1
Fastener
*2
Hog Ring
Remove the hog rings.

Detach the 2 hooks.

Detach the fastening tape.

Detach the 4 claws and remove the 2 front seat headrest supports.

Remove the seatback cover with pad.
| 18. REMOVE SEPARATE TYPE FRONT SEATBACK COVER |
Remove the hog rings and detach the fastening tape, and then remove the separate type front seatback cover from the separate type front seatback pad.

Text in Illustration *1
Hog Ring
*2
Fastening Tape
| 19. REMOVE FRONT SEATBACK PROTECTOR |
![]() ![]() |
Remove the front seatback protector.
Remove any remaining double-sided tape.
Text in Illustration *1
Double-sided Tape
| 20. REMOVE RECLINING ADJUSTER INSIDE COVER LH |
![]() ![]() |
Remove the screw.
Detach the guide and remove the reclining adjuster inside cover LH.
| 21. REMOVE RECLINING ADJUSTER INSIDE COVER RH |
- HINT:
- Use the same procedure described for the LH side.
| 22. REMOVE RECLINING ADJUSTER OUTSIDE COVER LH |
![]() ![]() |
Remove the screw and reclining adjuster outside cover LH.
| 23. REMOVE RECLINING ADJUSTER OUTSIDE COVER RH |
- HINT:
- Use the same procedure described for the LH side.
| 24. REMOVE FRONT SEAT LOWER CUSHION SHIELD RH |
![]() ![]() |
Detach the claw and remove the front seat lower cushion shield RH.
| 25. REMOVE FRONT SEAT INNER TRACK ASSEMBLY RH |
Using a screwdriver, detach the 2 springs and remove the seat track adjusting handle.

Using a T40 "TORX" socket wrench, remove the 5 "TORX" bolts and front seat inner track assembly RH.

| 26. REMOVE FRONT SEAT OUTER TRACK ASSEMBLY RH |
Using a T40 "TORX" socket wrench, remove the 5 "TORX" bolts and front seat outer track assembly RH together with the front seat reinforcement.

















