2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. INSTALL REAR SEAT CUSHION LOCK STRIKER SUB-ASSEMBLY

  1. Install the 4 strikers with the 10 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


    B184033E01


2. INSTALL REAR NO. 6 AIR DUCT (w/ Rear Air Conditioning System)
  1. Install the duct with the 5 screws.

  1. Connect the 2 connectors.

    E155886


3. INSTALL FRONT FLOOR CARPET ASSEMBLY
  1. Install the floor carpet.


4. INSTALL REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)

  1. B183334
    Attach the claw to install the guide.

  1. Install the screw.

    HINT:
    Use the same procedures for both sides.


5. INSTALL AIR DUCT PLUG (w/ Rear Air Conditioning System)

  1. B183333
    Attach the 2 claws to install the plug.

    HINT:
    Use the same procedures for both sides.


6. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
  1. w/ Sliding Roof:
    Install the front quarter trim panel assembly LH (Click here).

  1. w/o Sliding Roof:
    Install the front quarter trim panel assembly LH (Click here).


7. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH
  1. w/ Sliding Roof:
    Install the front quarter trim panel assembly RH (Click here).

  1. w/o Sliding Roof:
    Install the front quarter trim panel assembly RH (Click here).


8. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B190214

HINT:
Use the same procedure to install the rear seat cover cap on the other side.

  1. Attach the 3 claws to install the rear seat cover cap.


9. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Attach the 6 clips to install the support plate.


10. INSTALL REAR NO. 2 SEAT ASSEMBLY
  1. for Face to Face Seat Type:
    Install the rear No. 2 seat assembly (Click here).

  1. except Face to Face Seat Type:
    Install the rear No. 2 seat assembly (Click here).


11. INSTALL REAR DOOR SCUFF PLATE LH

B181674
  1. Attach the 3 claws and 4 clips to install the scuff plate.

  1. Install the screw.


12. INSTALL REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


13. INSTALL REAR STEP COVER

B181673

HINT:
Use the same procedure to install the step cover on the other side.

  1. Attach the 2 claws to install the step cover.


14. INSTALL REAR NO. 2 SEAT PROTECTOR

B184031E01
  1. Attach the 10 claws to install the 2 seat protectors.


15. INSTALL REAR NO. 1 SEAT PROTECTOR

B184032E01
  1. Attach the 10 claws to install the 2 seat protectors.


16. INSTALL REAR NO. 1 SEAT ASSEMBLY LH
  1. Install the rear No. 1 seat assembly LH (Click here).


17. INSTALL REAR NO. 1 SEAT ASSEMBLY RH

B181161E01
  1. Temporarily install the seat assembly with the 4 bolts.

    NOTICE:
    Be careful not to damage the vehicle body.

  1. Tighten the bolts in the order shown in the illustration.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }

  1. B181160
    w/ Rear Seat Side Airbag:
    Connect the connector.

  1. w/ Seat Heater System:
    Connect the connector.


18. INSTALL REAR NO. 3 SEAT CUSHION HINGE COVER

B181159
  1. Attach the 2 clips and 2 claws to install the cover.


19. INSTALL REAR NO. 1 SEAT CUSHION HINGE COVER

B181158
  1. Attach the 2 clips and 2 claws to install the cover.


20. INSTALL REAR NO. 4 SEAT CUSHION HINGE COVER
  1. Return the seat to the upright position.

  1. B258449
    Attach the 7 claws to install the cover.


21. INSTALL REAR NO. 2 SEAT CUSHION HINGE COVER

B258447
  1. Attach the 6 claws to install the cover.


22. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


23. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).


24. INSPECT REAR NO. 1 SEAT ASSEMBLY RH
  1. w/ Seat Heater System:
    Check the seat heater operation.

    1. Turn the ignition switch to ON.

    2. Turn the seat heater switch on.

    3. Wait 5 minutes or more and confirm that the seat surface becomes warm.

← REASSEMBLY (from Sep 2011)INSTALLATION (from Jan 2012) →