DISASSEMBLY
Removal / installation · Vehicles built from Sep 2011
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
- HINT:
- Use the same procedure for the RH and LH sides.
- The procedure listed below is for the LH side.
- Use the same procedure for the RH and LH sides.
| 1. REMOVE SEAT ADJUSTER BOLT COVER |
![]() ![]() |
Using a screwdriver, detach the 2 claws and remove the cover.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 2. REMOVE NO. 2 RECLINING ADJUSTER RELEASE HANDLE LH |
![]() ![]() |
Remove the screw and release handle.
| 3. REMOVE RECLINING ADJUSTER COVER LH |
![]() ![]() |
Remove the screw.
Detach the 3 claws in the order shown in the illustration, and then remove the cover.
| 4. REMOVE RECLINING ADJUSTER COVER RH |
![]() ![]() |
Remove the screw.
Detach the 5 claws in the order shown in the illustration, and then remove the cover.
| 5. REMOVE REAR SEAT REAR BRACKET COVER REAR |
Detach the 2 claws and cover.
| 6. REMOVE REAR NO. 3 SEAT LEG COVER LH |
Using a screwdriver, remove the spring of the seat stay ball-joint.

Disconnect the seat stay.
Remove the 2 screws and cover.

| 7. REMOVE NO. 2 SEAT LEG COVER NO. 2 |
Remove the screw and seat leg cover.

| 8. REMOVE 3RD SEAT LINK SUB-ASSEMBLY LH |
![]() ![]() |
Remove the bolt, nut and seat link.
| 9. REMOVE 3RD SEAT CUSHION LOCK COVER |
![]() ![]() |
Detach the 4 claws and remove the 2 covers.
| 10. REMOVE REAR SEAT CUSHION UNDER COVER LH |
Detach the 16 claws.

Remove the 7 screws and cover.

| 11. REMOVE NO. 3 SEAT FRONT BRACKET COVER LH |
![]() ![]() |
Detach the 4 claws and remove the cover.
| 12. REMOVE NO. 3 SEAT LEG COVER NO. 2 |
![]() ![]() |
Remove the 2 screws.
Detach the 4 claws and remove the cover.
| 13. REMOVE REAR SEAT LOCK COVER LH |
![]() ![]() |
Remove the 2 screws.
Detach the 2 clamps and remove the 2 covers.
| 14. REMOVE SEAT STAND FRAME CAP |
![]() ![]() |
Using a screwdriver, detach the 2 claws and remove the stand frame cap.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 15. REMOVE SEAT CUSHION LOCK RELEASE LEVER ASSEMBLY LH |
Remove the screw.

Detach the claw and remove the release lever.
Detach the cable clamp and disconnect the cable.

| 16. REMOVE REAR CENTER SEAT INNER BELT LH (w/ Rear Center Seat Headrest) |
![]() ![]() |
Remove the nut and belt.
- HINT:
- The rear No. 2 seat inner belt is fixed with the same nut as the rear seat inner belt. Therefore, it becomes disconnected when the nut is removed.
| 17. REMOVE REAR CENTER SEAT INNER BELT RH (w/ Rear Center Seat Headrest) |
![]() ![]() |
Remove the belt.
| 18. REMOVE REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY |
![]() ![]() |
Remove the nut and belt.
- HINT:
- The rear No. 2 seat inner belt is fixed with the same nut as the rear seat outer belt. Therefore, it becomes disconnected when the nut is removed.
| 19. REMOVE REAR SEAT CUSHION CARPET |
![]() ![]() |
Cut off the tack pins which fasten the seat cushion carpet to the seat cushion pad, and then remove the seat cushion carpet from the seat cushion pad.
| 20. REMOVE CAP |
Detach the 4 claws and remove the 2 caps.

| 21. REMOVE NO. 2 BOTTLE HOLDER |
Remove the 2 screws and No. 2 bottle holder.

| 22. REMOVE SEAT CUSHION COVER WITH PAD |
| 23. REMOVE NO. 3 SEAT CUSHION PAD LH |
| 24. REMOVE NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH |
w/o Bottle Holder:
Remove the hog rings.

Detach the fastening tape and remove the seat cushion cover.
Text in Illustration *1
Fastening Tape
w/ Bottle Holder:
Remove the hog rings.

Detach the 3 fastening tapes and remove the seat cushion cover.
Text in Illustration *1
Fastening Tape
| 25. REMOVE NO. 2 SEAT STAY SUB-ASSEMBLY |
![]() ![]() |
Remove the bolt and seat stay.
| 26. REMOVE NO. 3 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY |
Detach the 2 cable clamps and disconnect the 2 cables.

Detach the 2 clamps and remove the cable.

| 27. REMOVE REAR NO. 2 SEATBACK CUSHION |
![]() ![]() |
Remove the screw and seatback cushion.
| 28. REMOVE REAR LOWER SEATBACK LOCK BEZEL |
![]() ![]() |
Detach the 3 claws and clip, and then remove the seatback lock bezel.
| 29. REMOVE REAR SEAT HINGE PAWL GUIDE |
![]() ![]() |
Detach the 5 claws and remove the guide.
| 30. REMOVE REAR SEAT HINGE PAWL GUIDE |
![]() ![]() |
Remove the screw and guide.
| 31. REMOVE REAR SEAT HEADREST ASSEMBLY (w/ Folding Headrest) |
![]() ![]() |
While releasing the lock inside the headrest support with a screwdriver, remove the headrest.
- HINT:
- Tape the screwdriver tip before use.
Text in Illustration *1
Protective Tape
| 32. REMOVE REAR SEAT HEADREST ASSEMBLY (w/o Folding Headrest) |
| 33. REMOVE REAR SEAT HEADREST HANDLE |
![]() ![]() |
Remove the snap ring and headrest handle.
| 34. REMOVE SEATBACK COVER WITH PAD |
LH Side:
w/ Rear Center Headrest:
-
Open the fastener.

-
Detach the 2 hooks.

-
Pull out the center headrest storage bag.

- Remove the rear seat protector.
-
Detach the 8 claws and remove the 4 headrest supports.

-
w/o Rear Center Headrest:
-
Detach the hook.

- Remove the rear seat protector.
-
Detach the 4 claws and remove the 2 headrest supports.

-
RH Side:
Detach the hook.

Remove the rear seat protector.
Detach the 4 claws and remove the 2 headrest supports.

Remove the hog ring and seatback cover with pad.

| 35. REMOVE NO. 3 SEATBACK COVER SUB-ASSEMBLY LH |
![]() ![]() |
Remove the hog rings and seatback cover.
| 36. REMOVE REAR INNER SEAT RECLINING COVER LH |
![]() ![]() |
Remove the screw.
Detach the claw and remove the cover.
| 37. REMOVE REAR INNER SEAT RECLINING COVER RH |
Remove the screw.
Detach the claw and remove the cover.
| 38. REMOVE REAR SEAT LOCK CONTROL CABLE |
![]() ![]() |
Detach the 2 cable clamps and disconnect the 2 cables.
Detach the 2 clamps and remove the lock control cable.
| 39. REMOVE REAR SEATBACK LOCK STRIKER ASSEMBLY LH |
![]() ![]() |
Remove the 2 nuts and lock striker.
| 40. REMOVE REAR NO. 2 SEATBACK COVER LH |
Detach the 3 claws and remove the cover.
| 41. REMOVE REAR SEATBACK LOCK STRIKER COVER LH |
Detach the 2 clamps and remove the cover.
| 42. REMOVE NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY |
Remove the bolt and release handle.

























