2011-2013 Land Cruiser · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for the RH and LH sides.
  2. The procedure listed below is for the LH side.


1. INSTALL NO. 2 SEAT RECLINING RELEASE HANDLE SUB-ASSEMBLY
  1. Install the release handle with the bolt.


2. INSTALL REAR SEATBACK LOCK STRIKER COVER LH
  1. Attach the 2 clamps to install the cover.


3. INSTALL REAR NO. 2 SEATBACK COVER LH
  1. Attach the 3 claws to install the cover.


4. INSTALL REAR SEATBACK LOCK STRIKER ASSEMBLY LH

B181859
  1. Install the lock striker with the 2 nuts.

    Torque:
    14 N*m{ 138 kgf*cm , 10 ft.*lbf }


5. INSTALL REAR SEAT LOCK CONTROL CABLE

B181858
  1. Attach the 2 clamps to install the lock control cable.

  1. Attach the 2 cable clamps to connect the 2 cables.


6. INSTALL REAR INNER SEAT RECLINING COVER RH

B181857
  1. Attach the claw to install the cover.

  1. Install the screw.


7. INSTALL REAR INNER SEAT RECLINING COVER LH
  1. Attach the claw to install the cover.

  1. Install the screw.


8. INSTALL NO. 3 SEATBACK COVER SUB-ASSEMBLY LH

B184053E02
  1. Using hog ring pliers, install the seatback cover to the seatback pad with new hog rings.

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

    Text in Illustration 
    *1
    Hog Ring Pliers


9. INSTALL SEATBACK COVER WITH PAD

  1. B181851
    Using hog ring pliers, install the seatback cover with pad to the seatback frame with a new hog rings.

  1. LH Side:

    1. w/ Rear Center Seat Headrest:


      1. B181850
        Attach the 8 claws to install the 4 headrest supports.
      2. Install the rear seat protector.

      3. B184046
        Insert the center headrest storage bag.

      4. B181848
        Attach the 2 hooks.

      5. B184047
        Close the fastener.

    2. w/o Rear Center Seat Headrest:


      1. B235505
        Attach the 4 claws to install the 2 headrest supports.
      2. Install the rear seat protector.

      3. B235503
        Attach the hook.

  1. RH Side:

    1. B181854
      Attach the 4 claws to install the 2 headrest supports.

    2. Install the rear seat protector.

    3. B181853
      Attach the hook.


10. INSTALL REAR SEAT HEADREST HANDLE
  1. Install the snap ring to the headrest handle.

  1. B184054
    Install the headrest handle to the headrest.


11. INSTALL REAR SEAT HEADREST ASSEMBLY (w/ Folding Headrest)

B190319E02
  1. While releasing the lock inside the headrest support with a screwdriver, install the headrest.

    HINT:
    Tape the screwdriver tip before use.

    Text in Illustration 
    *1
    Protective Tape


12. INSTALL REAR SEAT HEADREST ASSEMBLY (w/o Folding Headrest)

13. INSTALL REAR SEAT HINGE PAWL GUIDE

B181846
  1. Install the guide with the screw.


14. INSTALL REAR SEAT HINGE PAWL GUIDE

B181845
  1. Attach the 5 claws to install the guide.


15. INSTALL REAR LOWER SEATBACK LOCK BEZEL

B181844
  1. Attach the 3 claws and clip to install the seatback lock bezel.


16. INSTALL REAR NO. 2 SEATBACK CUSHION

B181843
  1. Install the seatback cushion with the screw.


17. INSTALL NO. 3 FOLD SEAT LOCK CONTROL CABLE ASSEMBLY

  1. B235502
    Attach the 2 clamps to install the 2 cables.

  1. B181838
    Attach the 2 cable clamps to connect the 2 cables.


18. INSTALL NO. 2 SEAT STAY SUB-ASSEMBLY

B181839
  1. Install the seat stay with the bolt.


19. INSTALL NO. 3 SEAT CUSHION COVER SUB-ASSEMBLY LH

  1. B263633E01
    w/o Bottle Holder:

    1. Attach the fastening tape to install the seatback cover.

    2. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

      Text in Illustration 
      *1
      Hog Ring Pliers
      *2
      Fastening Tape

  1. B263634E01
    w/ Bottle Holder:

    1. Attach the 3 fastening tapes to install the seatback cover.

    2. Using hog ring pliers, install the seat cushion cover to the seat cushion pad with new hog rings.

      NOTICE:
      1. Be careful not to damage the cover.
      2. When installing the hog rings, avoid wrinkling the cover.

      Text in Illustration 
      *1
      Hog Ring Pliers
      *2
      Fastening Tape


20. INSTALL NO. 3 SEAT CUSHION PAD LH

21. INSTALL SEAT CUSHION COVER WITH PAD

22. INSTALL NO. 2 BOTTLE HOLDER

  1. B235484
    Install the No. 2 bottle holder with the 2 screws.


23. INSTALL CAP

  1. B235506
    Attach the 4 claws to install the 2 caps.


24. INSTALL REAR SEAT CUSHION CARPET

B181840
  1. Install the seat cushion carpet with new tack pins.


25. INSTALL REAR NO. 2 SEAT INNER BELT SUB-ASSEMBLY

  1. Install the 2 belts.

    B184524E01

    NOTICE:
    1. Make sure the claws are facing away from the seat.
    2. Do not overlap the anchor part of the seat belt and protruding parts of the seat.


26. INSTALL REAR CENTER SEAT INNER BELT LH (w/ Rear Center Seat Headrest)

B180632E01
  1. Install the belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the seat.

    HINT:
    The rear No. 2 seat inner belt is fixed with the same nut as the rear seat inner belt. Therefore, connect it when installing the rear seat inner belt.


27. INSTALL REAR CENTER SEAT INNER BELT RH (w/ Rear Center Seat Headrest)

B180634E01
  1. Install the belt with the nut.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not overlap the anchor part of the seat belt and protruding parts of the seat.

    HINT:
    The rear No. 2 seat inner belt is fixed with the same nut as the rear seat outer belt. Therefore, connect it when installing the rear seat outer belt.


28. INSTALL SEAT CUSHION LOCK RELEASE LEVER ASSEMBLY LH

  1. B235501
    Attach the cable clamp to connect the cable.

  1. B235509
    Attach the claw to install the release lever.

  1. Install the screw.


29. INSTALL SEAT STAND FRAME CAP

B184049
  1. Attach the 2 claws to install the stand frame cap.


30. INSTALL REAR SEAT LOCK COVER LH

B181831
  1. Attach the 2 clamps to install the cover.

  1. Install the 2 screws.


31. INSTALL NO. 3 SEAT LEG COVER NO. 2

B181830
  1. Attach the 4 claws to install the cover.

  1. Install the 2 screws.


32. INSTALL NO. 3 SEAT FRONT BRACKET COVER LH

B181829
  1. Attach the 4 claws to install the cover.


33. INSTALL REAR SEAT CUSHION UNDER COVER LH

  1. B258453
    Install the cover with the 7 screws.

  1. B181827
    Attach the 16 claws.


34. INSTALL 3RD SEAT CUSHION LOCK COVER

B181826
  1. Attach the 4 claws to install the 2 covers.


35. INSTALL 3RD SEAT LINK SUB-ASSEMBLY LH

B181825
  1. Install the seat link with the bolt and nut.

    Torque:
    8.5 N*m{ 87 kgf*cm , 75 in.*lbf }


36. INSTALL NO. 2 SEAT LEG COVER NO. 2

B182643
  1. Install the seat leg cover with the screw.


37. INSTALL REAR NO. 3 SEAT LEG COVER LH

  1. B181823
    Install the seat leg cover with the 2 screws.

  1. B184055
    Install the spring of the seat stay ball-joint.

  1. Connect the seat stay to the seat frame.


38. INSTALL REAR SEAT REAR BRACKET COVER REAR
  1. Attach the 2 claws to install the cover.


39. INSTALL RECLINING ADJUSTER COVER RH

B181821E02
  1. Attach the 5 claws in the order shown in the illustration to install the cover.

  1. Install the screw.


40. INSTALL RECLINING ADJUSTER COVER LH

B181820E02
  1. Attach the 3 claws in the order shown in the illustration to install the cover.

  1. Install the screw.


41. INSTALL NO. 2 RECLINING ADJUSTER RELEASE HANDLE LH

B181819
  1. Install the release handle with the screw.


42. INSTALL SEAT ADJUSTER BOLT COVER

B184050
  1. Attach the 2 claws to install the cover.

← DISASSEMBLY (from Sep 2011)INSTALLATION (Sep 2011 – Dec 2011) →