2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.

HINT:
  1. Use the same procedure for RHD and LHD vehicles.
  2. The procedure listed below is for LHD vehicles.


1. REMOVE FRONT SEAT ASSEMBLY LH
(Click here)

2. REMOVE SLIDE AND VERTICAL POWER SEAT SWITCH KNOB

B180697E02
  1. Apply protective tape as shown in the illustration.

    Text in Illustration 
    *1
    Protective Tape

  1. Using a screwdriver, detach the 2 claws and remove the slide and vertical power seat switch knob.

    HINT:
    Tape the screwdriver tip before use.


3. REMOVE RECLINING POWER SEAT SWITCH KNOB

B180698E02
  1. Using a screwdriver, detach the 2 claws and remove the reclining power seat switch knob.

    Text in Illustration 
    *1
    Protective Tape

    HINT:
    Tape the screwdriver tip before use.


4. REMOVE FRONT SEAT CUSHION SHIELD LH

B180699
  1. Remove the 2 screws.

  1. Disconnect the 2 rubber bands.

  1. B180700
    Remove the 3 screws.

  1. Detach the 2 claws and remove the front seat cushion shield LH together with the front inner No. 1 seat cushion shield LH.

  1. for Driver Side:
    Disconnect the connector.


5. REMOVE FRONT SEAT INNER BELT ASSEMBLY LH
  1. Disconnect the connectors and detach the clamps.

  1. B185874
    Remove the nut and front seat inner belt assembly.


6. REMOVE FRONT INNER SEAT CUSHION SHIELD LH

B180703
  1. Remove the screw.

  1. Detach the 2 claws and clip, and then remove the front inner seat cushion shield LH.


7. REMOVE FRONT SEATBACK BOARD SUB-ASSEMBLY LH

B180711
  1. Remove the 2 screws.

  1. Move the front seatback board sub-assembly LH in the direction of the arrow to detach the 2 hooks and remove it.


8. REMOVE SEAT CLIMATE CONTROL CONTROLLER LH (w/ Climate Control Seat System)

B299415
  1. Detach the 2 claws and disconnect the seat climate control blower LH.

  1. Detach the 4 hooks and remove the seat climate control controller LH.


9. REMOVE FRONT SEAT HEADREST SUPPORT

B180712
  1. Detach the 4 claws and remove the 2 front seat headrest supports.


10. REMOVE SEATBACK COVER WITH PAD

  1. B180706
    w/o Climate Control Seat System:
    Disconnect the connector and detach the 2 wire harness clamps.

  1. B299194
    w/ Climate Control Seat System:
    Disconnect the 2 connectors and detach the 4 wire harness clamps.

  1. B180713E02
    Remove the hog rings.
    Text in Illustration 
    *1
    Hog Ring

  1. B180716
    Remove the nut and detach the seatback cover bracket.
    Text in Illustration 
    *1
    Seatback Cover Bracket

  1. Detach the hooks and remove the seatback cover with pad.


11. REMOVE FRONT SEATBACK PROTECTOR

B299469E01
  1. Remove the front seatback protector.

  1. Remove any remaining double-sided tape.

    Text in Illustration 
    *1
    Double-sided Tape


12. REMOVE LUMBAR SUPPORT ADJUSTER ASSEMBLY LH

  1. B299472E01
    Remove the cable clamp and disconnect the active headrest cable from the seatback spring.
    Text in Illustration 
    *1
    Cable Clamp
    *2
    Hook

  1. Remove the 4 springs.

  1. Detach the 4 hooks and remove the seatback spring.

  1. B299473
    Disconnect the connector.

  1. Remove the 2 screws and lumbar support adjuster assembly LH.

← REMOVAL (Sep 2011 – Dec 2011)INSPECTION (from Sep 2011) →