2011-2013 Land Cruiser · Service Manual Steering

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL STEERING WHEEL BOSS LOWER COVER

  1. C246491
    Attach the 4 claws and 2 screws and install the steering wheel boss lower cover.


2. INSTALL STEERING SHAKE DAMPER

  1. C246801
    Install the 2 screws to steering shake damper.


3. INSTALL STEERING PAD COVER LH (w/o Steering Pad Switch)

  1. C246800E01
    Install the screw and 4 guide pins, install the steering pad cover LH.


4. INSTALL STEERING PAD COVER RH (w/o Steering Pad Switch)

HINT:
Use the same procedures described for the LH side.


5. INSTALL STEERING WHEEL HEATER CONTROL ASSEMBLY (w/ Steering Heater)
  1. Install the steering wheel heater control assembly to the lower steering wheel boss cover with the 2 screws.

  1. Attach the connector clamp.

  1. Connect the 2 connectors.


6. ADJUST SPIRAL CABLE
  1. Check that the ignition switch is off.

  1. Check that the cable is disconnected from the battery negative (-) terminal.

    CAUTION:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

  1. B181594
    Rotate the spiral cable with steering sensor counterclockwise slowly by hand until it feels firm.

    CAUTION:
    Do not turn the spiral cable with steering sensor by the airbag wire harness.

  1. B181595E01
    Rotate the spiral cable with steering sensor clockwise approximately 2.5 turns to align the marks.

    CAUTION:
    Do not turn the spiral cable with spiral sensor by the airbag wire harness.

    HINT:
    The spiral cable with steering sensor will rotate approximately 2.5 turns to both the left and right from the center.


7. INSTALL STEERING WHEEL ASSEMBLY

  1. C174823E02
    Align the matchmarks on the steering wheel assembly and steering main shaft assembly.
    Text in Illustration 
    *a
    Matchmark

  1. Install the steering wheel assembly set nut.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }


8. INSTALL CRUISE CONTROL MAIN SWITCH (w/ Cruise Control System)

  1. B179762
    Install the switch.

  1. B179760
    Install the 2 screws.

  1. B179759
    Connect the connector and clamp.


9. INSTALL STEERING PAD SWITCH ASSEMBLY (w/ Steering Pad Switch)

  1. C172683
    Attach the 4 claws to install the steering pad switch.

  1. Install the 2 screws.

  1. Connect the connector.


10. INSTALL STEERING PAD (w/ Airbag System)
  1. With the steering pad installed on the vehicle, perform a visual check. If there are any defects as mentioned below, replace the steering pad with a new one:
    Cuts, minute cracks or marked discoloration on the steering pad top surface or in the grooved portion.

  1. Make sure that the horn sounds.

    HINT:
    If the horn does not sound, inspect the horn system.


11. INSTALL STEERING PAD (w/o Airbag System)

HINT:
Refer to the step "INSTALL STEERING PAD (w/ Airbag System)".


12. INSTALL LOWER NO. 2 STEERING WHEEL COVER

  1. B189186E01
    Attach the 2 claws to install the cover.


13. INSTALL LOWER NO. 3 STEERING WHEEL COVER

  1. B181563
    Attach the 2 claws to install the cover.


14. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


15. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →