2011-2013 Land Cruiser · Service Manual Steering

INSPECTION

Inspection · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

CAUTION:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the PRECAUTION in the SRS (Click here).


INSPECT STEERING PAD SWITCH ASSEMBLY (w/o Radio Receiver)

Disconnect the z35 switch connector.

E158678E01
Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
2 (-DP) - 7 (+DP)
DISP switch pushed
Below 1 Ω

If the result is not as specified, replace the steering switch assembly.

INSPECT STEERING PAD SWITCH ASSEMBLY (w/ Multi-display)

  1. Disconnect the z35 switch connector.

    E155690E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    10 (AU1) - 8 (EAU)
    No switch is pushed
    100 kΩ
    10 (AU1) - 8 (EAU)
    Seek+ switch pushed
    Below 1 Ω
    10 (AU1) - 8 (EAU)
    Seek- switch pushed
    330 Ω
    10 (AU1) - 8 (EAU)
    Volume+ switch pushed
    1010 Ω
    10 (AU1) - 8 (EAU)
    Volume- switch pushed
    3210 Ω
    9 (AU2) - 8 (EAU)
    No switch is pushed
    100 kΩ
    9 (AU2) - 8 (EAU)
    MODE switch pushed
    Below 1 Ω
    9 (AU2) - 8 (EAU)
    ON Hook switch pushed
    330 Ω
    9 (AU2) - 8 (EAU)
    OFF Hook switch pushed
    1010 Ω
    9 (AU2) - 8 (EAU)
    Voice switch pushed
    3210 Ω
    7 (+DP) - 8 (EAU)
    DISP switch pushed
    Below 1 Ω

    If the result is not as specified, replace the steering switch assembly.


INSPECT STEERING PAD SWITCH ASSEMBLY (w/o Multi-display)

  1. Disconnect the z35 switch connector.

    E155692E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    10 (AU1) - 8 (EAU)
    No switch is pushed
    100 kΩ
    10 (AU1) - 8 (EAU)
    Seek+ switch pushed
    Below 1 Ω
    10 (AU1) - 8 (EAU)
    Seek- switch pushed
    330 Ω
    10 (AU1) - 8 (EAU)
    Volume+ switch pushed
    1000 Ω
    10 (AU1) - 8 (EAU)
    Volume- switch pushed
    3210 Ω
    9 (AU2) - 8 (EAU)
    No switch is pushed
    100 kΩ
    9 (AU2) - 8 (EAU)
    MODE switch pushed
    Below 1 Ω
    7 (+DP) - 8 (EAU)
    DISP switch pushed
    Below 1 Ω

    If the result is not as specified, replace the steering pad switch assembly.

← REMOVAL (from Jan 2012)INSPECTION (from Jan 2012) →