Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011from Jan 2012
1.
HANDLING PRECAUTIONS FOR STEERING ACTUATOR ASSEMBLY
NOTICE:
Be careful that the No. 2 seal lip or boot does not turn outward while carrying or installing the steering actuator assembly. If installing a new steering actuator assembly, make sure that the spiral center lock pin is securely inserted.
Do not use the steering actuator assembly if it has been dropped.
2.
INSTALL STEERING ACTUATOR ASSEMBLY
Make sure that the power steering link assembly is centered.
Install the steering actuator assembly.
If installing a new steering actuator assembly: Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.
NOTICE:
Do not pull out the center lock pin.
If reinstalling the removed steering actuator assembly:
Slowly turn the spiral case clockwise until it locks.
Turn the spiral case two turns counterclockwise from the lock position.
Align the slit of the sliding yoke with the alignment mark (▲).
Install the steering actuator assembly with the white paint on the upper surface of the spiral case facing down.
Align the matchmarks on the No. 2 steering intermediate shaft and steering actuator.
NOTICE:
Do not fold back the boot part of the steering hole cover or turn it excessively. If it is turned excessively, return it to its original position.
Do not turn the actuator body and the spiral case.
HINT:
Install the steering actuator from the inside of the vehicle.
Install the bolt.
Torque:
35 N*m{
360 kgf*cm
, 26 ft.*lbf
}
Using needle nose pliers, lock the clamp to the steering column hole cover to install it.
NOTICE:
Be careful when performing the operation as the clamp may not lock if the claws of the clamp are deformed.
Move the lock in the direction of the arrow and connect the steering actuator connector.
HINT:
When a new actuator is installed, remove the center lock pin.
Connect the connector.
3.
INSTALL STEERING COLUMN ASSEMBLY
Align the matchmarks on the steering actuator and steering column.
Install the bolt.
Torque:
35 N*m{
360 kgf*cm
, 26 ft.*lbf
}
Install the steering column with the 4 nuts.
Torque:
26 N*m{
265 kgf*cm
, 19 ft.*lbf
}
4.
INSTALL NO. 3 AIR DUCT SUB-ASSEMBLY
Attach the 2 claws to install the duct.
Install the clip.
5.
CONNECT WIRE HARNESS PROTECTOR AND WIRE HARNESS
Attach the 3 claws to connect the wire harness protector and wire harness.
6.
INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)
Connect the connector.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
Install the driver side knee airbag with the 5 bolts.
Attach the 7 claws to install the No. 2 instrument panel finish panel cushion.
20.
INSTALL COMBINATION SWITCH ASSEMBLY WITH SPIRAL CABLE SUB-ASSEMBLY
Using pliers, grip the claws of the clamp and install the combination signal switch assembly with spiral cable sub-assembly to the steering column assembly with the clamp.
Connect the 5 connectors to the combination switch with spiral cable.
21.
INSTALL TILT AND TELESCOPIC SWITCH
Attach the claw to install the switch.
Connect the switch connector.
22.
INSTALL UPPER STEERING COLUMN COVER
Attach the claw to install the upper steering column cover.
Attach the 4 clips to the instrument cluster finish panel.
23.
INSTALL LOWER STEERING COLUMN COVER
Attach the 2 claws to install the lower steering column cover.
NOTICE:
Do not damage the tilt and telescopic switch.
Install the 3 screws.
Torque:
1.5 N*m{
15 kgf*cm
, 13 in.*lbf
}
24.
INSTALL STEERING WHEEL ASSEMBLY
Align the matchmarks on the steering wheel assembly and steering main shaft assembly.
Install the steering wheel assembly set nut.
Torque:
50 N*m{
510 kgf*cm
, 37 ft.*lbf
}
25.
INSTALL STEERING PAD
Support the steering pad with one hand.
Connect the 2 connectors to the steering pad.
NOTICE:
When handling the airbag connector, take care not to damage the airbag wire harness.
Connect the horn connector.
Confirm that the circumference groove of the "TORX" screw fits in the screw case, and place the steering pad onto the steering wheel.
Using a T30 "TORX" socket wrench, tighten the 2 screws.
Torque:
8.8 N*m{
90 kgf*cm
, 78 in.*lbf
}
26.
INSTALL LOWER NO. 2 STEERING WHEEL COVER
Attach the 2 claws to install the cover.
27.
INSTALL LOWER NO. 3 STEERING WHEEL COVER
Attach the 2 claws to install the cover.
28.
CONNECT CABLE TO NEGATIVE BATTERY TERMINAL
NOTICE:
Reset the AUTO TILT AWAY function setting to the previous condition by changing the customize parameter (Click here).
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).