2011-2013 Land Cruiser · Service Manual Suspension

INSTALLATION

Removal / installation · Vehicles built from Sep 2011

HINT:
  1. Use the same procedures for the RH side and LH side.
  2. The procedures listed below are for the LH side.
  3. A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL REAR NO. 2 SUSPENSION CONTROL ACCUMULATOR BRACKET LH
  1. Install the bracket to the shock absorber control valve with the bolt.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }


2. INSTALL REAR SHOCK ABSORBER CONTROL VALVE ASSEMBLY LH

  1. C172669
    Install the bracket to the control valve with the 3 bolts.

    Torque:
    18 N*m{ 184 kgf*cm , 13 ft.*lbf }

  1. C172668
    Install the control valve together with the bracket to the vehicle with the 3 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. Connect the control valve connector.

  1. C172804E01
    Connect the wire harness clamp to the control valve bracket.

  1. Install a new gasket to the No. 4 suspension control pressure hose, and connect the hose to the control valve with the union bolt.

    Torque:
    50 N*m{ 510 kgf*cm , 37 ft.*lbf }

  1. C178069E01
    Using a union nut wrench, connect the No. 4 height control tube to the control valve.

    Torque:
    without union nut wrench:
    44 N*m{ 450 kgf*cm , 33 ft.*lbf }
    with union nut wrench:
    40 N*m{ 408 kgf*cm , 30 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.


3. INSTALL REAR NO. 3 SUSPENSION CONTROL ACCUMULATOR LH
  1. Apply a small amount of suspension fluid to a new O-ring and new back-up ring and install them to the accumulator.

  1. C176191
    Install the No. 3 control accumulator to the control valve.

    Torque:
    150 N*m{ 1530 kgf*cm , 111 ft.*lbf }


4. INSTALL REAR SUSPENSION CONTROL ACCUMULATOR ASSEMBLY LH
  1. Apply a small amount of suspension fluid to a new O-ring and install it to the accumulator.

  1. C179740
    Install the control accumulator to the control valve.

    Torque:
    57 N*m{ 585 kgf*cm , 42 ft.*lbf }


5. BLEED AIR FROM SUSPENSION FLUID

  1. C176402
    With the engine stopped, fill the reservoir tank with fluid.

    NOTICE:
    When the engine starts, the pump operates and fluid is supplied to each cylinder from the reservoir tank. Therefore, add the necessary amount of fluid so that the reservoir tank does not become empty.

    HINT:
    At this point, the vehicle height is low because the pressure of the cylinders is low.

  1. With the vehicle on a level surface, start the engine and set the vehicle height to NORMAL with the suspension control switch.

  1. When the vehicle height becomes NORMAL and the pump stops, stop the engine.

  1. C172939
    Connect a hose to the bleeder plug of the front left side or right side control valve, then loosen the bleeder plug.

    CAUTION:
    Be careful when loosening the control valve bleeder plug because the front vehicle height drops rapidly.

  1. After the fluid containing air stops coming out, retighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    HINT:
    If the procedures are performed for the first time on the left side, perform the procedures on the right side for the second time.

  1. C172940
    Connect a hose to the bleeder plug of the rear left side or right side control valve, then loosen the bleeder plug.

    CAUTION:
    Be careful when loosening the control valve bleeder plug because the rear vehicle height drops rapidly.

  1. After the fluid containing air stops coming out, retighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    HINT:
    If the procedures are performed for the first time on the left side, perform the procedures on the right side for the second time.

  1. Repeat the previous 4 procedures until the fluid containing air stop coming out.


6. CHECK FLUID LEVEL IN RESERVOIR

  1. C176461
    With the vehicle empty, after setting the vehicle height to NORMAL from LO, check the indicator to make sure the vehicle height is NORMAL and check that the fluid level in the reservoir tank is within the specified range (MAX, MIN).

    HINT:
    After changing the vehicle height from LO to NORMAL, do not stop the engine for 25 seconds because the pressure control for the main accumulator is operating. After that, check the fluid level.


7. INSPECT FOR SUSPENSION FLUID LEAK
  1. Check that the union nuts shown in the illustration are tightened to the specified torque.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.

  1. Check for fluid leakage from the parts and connections.

    C176381E01

    HINT:
    For union nuts and union bolts not shown in the illustration, refer to the installation procedures for each title.


8. INSTALL HEIGHT CONTROL UNIT PROTECTOR ASSEMBLY LH

  1. Install the protector pipe with the 6 bolts.

    Torque:
    16 N*m{ 163 kgf*cm , 12 ft.*lbf }


    C179788


9. INSTALL SIDE STEP ASSEMBLY LH

  1. Install the side step with the 6 bolts.

    Torque:
    30 N*m{ 306 kgf*cm , 22 ft.*lbf }


    B180949

← INSPECTION (from Sep 2011)DISPOSAL (from Sep 2011) →