2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL REAR COOLING UNIT ASSEMBLY

  1. Install the rear cooling unit as shown in the illustration.

    E156487

  1. E154871
    Install the 4 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }

  1. Connect the connector.


2. INSTALL REAR ROOF NO. 1 AIR DUCT

E154870
  1. Install the duct with the clip.

  1. E154869
    Attach the 2 claws to install the cooler plate.


3. CONNECT AIR CONDITIONER TUBE AND ACCESSORY ASSEMBLY

E154366
  1. Remove the attached vinyl tape from the pipe.

  1. Sufficiently apply compressor oil to 2 new O-rings and the fitting surface of the air conditioner tube and accessory assembly.

  1. Install the 2 O-rings to the air conditioner tube and accessory assembly.

  1. Connect the air conditioner tube and accessory assembly.

  1. Install the 2 bolts.

    Torque:
    5.4 N*m{ 55 kgf*cm , 48 in.*lbf }


4. INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH
  1. w/ Sliding Roof:
    (Click here)

  1. w/o Sliding Roof:
    (Click here)


5. INSTALL REAR SEAT COVER CAP (w/ Rear No. 2 Seat)
  1. w/ Sliding Roof:
    (Click here)

  1. w/o Sliding Roof:
    (Click here)


6. INSTALL TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Install the tonneau cover assembly.


7. INSTALL REAR DOOR SCUFF PLATE LH
  1. w/ Sliding Roof:
    (Click here)

  1. w/o Sliding Roof:
    (Click here)


8. INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
  1. w/ Sliding Roof:
    (Click here)

  1. w/o Sliding Roof:
    (Click here)


9. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


10. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    Standard: 
    Condenser Core Thickness
    Air Conditioning Type
    Cool Box
    Refrigerant Charging Amount
    22 mm (0.866 in.)
    w/o Rear Cooler
    w/ Cool Box
    870 +/-30 g (30.7 +/-1.1 oz.)
    w/o Cool Box
    870 +/-30 g (30.7 +/-1.1 oz.)
    w/ Rear Cooler
    w/ Cool Box
    1010 +/-30 g (35.6 +/-1.1 oz.)
    w/o Cool Box
    960 +/-30 g (33.9 +/-1.1 oz.)
    16 mm (0.630 in.)
    w/o Rear Cooler
    w/ Cool Box
    770 +/-30 g (27.2 +/-1.1 oz.)
    w/o Cool Box
    770 +/-30 g (27.2 +/-1.1 oz.)
    w/ Rear Cooler
    w/ Cool Box
    970 +/-30 g (34.2 +/-1.1 oz.)
    w/o Cool Box
    920 +/-30 g (32.5 +/-1.1 oz.)

    I037365E19

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    2. Approximately 200 g (7.05 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.


11. WARM UP ENGINE
  1. Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch is on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


12. CHECK FOR REFRIGERANT GAS LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).

  1. I042222E21
    Using a halogen leak detector, check the refrigerant line for leakage.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.


13. CHECK SRS WARNING LIGHT
(Click here)

14. INSTALL UPPER RADIATOR SUPPORT SEAL

  1. Install the radiator support seal with the 7 clips.

    B180890E02

← INSTALLATION (Sep 2011 – Dec 2011)COMPONENTS (from Sep 2011) →