C1782 Power Source Voltage Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
| DTC Code |
Detection Condition |
Trouble Area |
| C1782 |
While the engine switch is on (IG), voltage at terminal IG, BAT and/or BAT2 is 10 V or less, or 16 V or more for 0.5 seconds. |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Even if DTC C1781 is stored at the same time, perform the inspection for DTC C1782 first.
- Before performing troubleshooting, inspect the connectors of related circuits.
- If the suspension control ECU or height control sensor is replaced, the vehicle height offset calibration must be performed (Click here).
- Even if DTC C1781 is stored at the same time, perform the inspection for DTC C1782 first.
| 1. READ VALUE USING INTELLIGENT TESTER (IG VOLTAGE) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and the tester on.
Read the "IG Power Source Voltage" item in the Data List.
AHC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
IG Power Source Voltage
Power supply voltage /
min.: 0 V
max.: 255 V
Engine switch on (IG): 11 to 14 V
-
- OK:
- 11 to 14 V
|
|
||||
| OK | |
| 2. RECONFIRM DTC OUTPUT |
Clear the DTCs (Click here).
Check for DTCs.
Result Result
Proceed to
DTC is output
A
DTC is not output
B
|
|
||||
| A | |
| 3. READ VALUE USING INTELLIGENT TESTER (+B POWER SOURCE VOLTAGE, +B2 POWER SOURCE VOLTAGE) |
Connect the intelligent tester to the DLC3.
Turn the engine switch on (IG) and the tester on.
Read the "+B Power Source Voltage" and "+B2 Power Source Voltage" items in the Data List.
AHC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
+B Power Source Voltage
Power supply for absorber control actuator /
min.: 0 V
max.: 255 V
Engine switch on (IG): 11 to 14 V
-
+B2 Power Source Voltage
Power supply for No. 1 height control valve and front suspension control valve /
min.: 0 V
max.: 255 V
Engine switch on (IG): 11 to 14 V
-
- OK:
- 11 to 14 V
|
|
||||
| OK | ||
| ||
| 4. INSPECT FUSE (AHC-B, AHC-B NO. 2) |
Remove the AHC-B and AHC-B No. 2 fuses from the cowl side junction block RH.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
AHC-B fuse
Always
Below 1 Ω
AHC-B No. 2 fuse
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (BATTERY - SUSPENSION CONTROL ECU) |
Disconnect the K34 and K35 ECU connectors.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
K34-3 (BAT2) - Body ground
Engine switch on (IG)
11 to 14 V
K35-1 (BAT) - Body ground
Engine switch on (IG)
11 to 14 V
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (BATTERY - ECU AND BODY GROUND) |
![]() ![]() |
Disconnect the K34 ECU connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
K34-5 (IG) - Body ground
Engine switch on (IG)
11 to 14 V
Result Result
Proceed to
OK
A
NG (1UR-FE)
B
NG (1VD-FTV)
C
|
|
||||
|
|
||||
| A | ||
| ||

