2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the cables from the negative (-) main battery and sub-battery terminals.


2. REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)
  1. Remove the rear No. 1 seat assembly RH (Click here).


3. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)
  1. Remove the rear No. 1 seat assembly LH (Click here).


4. REMOVE REAR NO. 2 SEAT ASSEMBLY
  1. for Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).

  1. except Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).


5. REMOVE REAR STEP COVER

B181673

HINT:
Use the same procedure to remove the step cover on the other side.

  1. Detach the 2 claws and remove the step cover.


6. REMOVE REAR DOOR SCUFF PLATE LH

B181674
  1. Remove the screw.

  1. Detach the 3 claws and 4 clips, and remove the scuff plate.


7. REMOVE REAR DOOR SCUFF PLATE RH

HINT:
Use the same procedures described for the LH side.


8. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE

B181672
  1. Detach the 6 clips and remove the support plate.


9. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat, except Face to Face Seat Type)

B190187E01

HINT:
Use the same procedure to remove the rear seat cover cap on the other side.

  1. Using a screwdriver, detach the 3 claws and remove the rear seat cover cap.

    HINT:
    Tape the screwdriver tip before use.


10. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH
  1. w/ Sliding Roof:
    Remove the front quarter trim panel assembly LH (Click here).

  1. w/o Sliding Roof:
    Remove the front quarter trim panel assembly LH (Click here).


11. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH
  1. w/ Sliding Roof:
    Remove the front quarter trim panel assembly RH (Click here).

  1. w/o Sliding Roof:
    Remove the front quarter trim panel assembly RH (Click here).


12. REMOVE AIR DUCT PLUG (w/ Rear Air Conditioning System)

  1. B183333
    Detach the 2 claws and remove the plug.

    HINT:
    Use the same procedures for both sides.


13. REMOVE REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)

  1. B183334
    Remove the screw.

  1. Detach the claw and remove the guide.

    HINT:
    Use the same procedures for both sides.


14. SEPARATE REAR FLOOR MAT ASSEMBLY

A176328
  1. w/ Rear Air Conditioning System:
    Detach the 5 clips and fold back the floor mat toward the front of the vehicle.

    HINT:
    Fold back the floor mat so that the rear No. 7 air duct can be removed.

  1. w/o Rear Air Conditioning System:
    Detach the 5 clips and fold back the floor mat toward the front of the vehicle.

    HINT:
    Fold back the floor mat so that the service hole cover can be removed.


15. REMOVE REAR NO. 7 AIR DUCT (w/ Rear Air Conditioning System)

  1. A176392
    Detach the 4 clips and remove the air duct.


16. REMOVE REAR FLOOR SERVICE HOLE COVER

A176326

17. REMOVE FUEL SENDER GAUGE ASSEMBLY

  1. A176327
    Disconnect the sender gauge connector.

  1. Remove the 5 screws and sender gauge.

    NOTICE:
    Be careful not to bend the arm of the fuel sender gauge.

  1. Remove the gasket from the sender gauge.

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →