2011-2013 Land Cruiser · Service Manual Vehicle Interior

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

HINT:
A bolt without a torque specification is shown in the standard bolt chart (Click here).


1. INSTALL COOLING BOX ASSEMBLY

B182475
  1. Attach the 2 claws.

  1. Connect the connector.

  1. Sufficiently apply compressor oil to 2 new O-rings.

    Compressor oil:
    ND-OIL 8 or equivalent

  1. Install the 2 O-rings on the 2 cooler pipes.

  1. Connect the 2 cooler pipes with the 2 bolts.

    Torque:
    9.8 N*m{ 100 kgf*cm , 87 in.*lbf }

  1. Install the cooling box with the 4 bolts and 2 screws.


2. INSTALL REAR CONSOLE END PANEL SUB-ASSEMBLY

  1. B182503
    Connect the connectors and 2 clamps.

  1. Attach the 8 claws to install the end panel.


3. INSTALL NO. 1 COOLER COVER

  1. B183312
    Attach the claw on the upper part of the cooler cover, and then attach the clamp on the lower part of the cooler cover to install it.


4. INSTALL UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B180011
    Connect the connectors.

  1. Attach the 14 claws to install the console panel.


5. INSTALL CONSOLE CUP HOLDER BOX SUB-ASSEMBLY

  1. B180010
    Attach the 4 claws to install the box.


6. INSTALL REAR UPPER CONSOLE PANEL SUB-ASSEMBLY

  1. B180009
    Attach the 9 claws to install the panel.


7. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B180006
    Connect the connectors.

  1. Attach the 7 claws to install the panel.


8. INSTALL SHIFT LEVER KNOB SUB-ASSEMBLY

  1. Install the shift lever knob and twist it in the direction indicated by the arrow.

    B186291E01


9. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH

  1. B180005
    Attach the 7 claws to install the panel pad.

  1. Install the screw.

  1. Install the clip.


10. INSTALL NO. 1 INSTRUMENT PANEL FINISH CUSHION

  1. B182501
    Attach the 7 claws to install the panel cushion.


11. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

  1. B181910
    Connect the connectors and 2 clamps.

  1. Attach the 8 claws to install the panel pad.

  1. Install the screw.

  1. Install the clip.


12. INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

  1. E155134
    Attach the 7 claws to install the panel cushion.


13. INSTALL FRONT SEAT ASSEMBLY LH (for Manual Seat)
  1. Install the front seat assembly LH (Click here).


14. INSTALL FRONT SEAT ASSEMBLY LH (for Power Seat)
  1. Install the front seat assembly LH (Click here).


15. CHARGE REFRIGERANT
SST
09985-20010   (09985-02130, 09985-02150, 09985-02090, 09985-02110, 09985-02010, 09985-02050, 09985-02060, 09985-02070)
  1. Perform vacuum purging using a vacuum pump.

  1. Charge refrigerant HFC-134a (R134a).

    Standard: 
    Condenser Core Thickness
    Air Conditioning Type
    Cool Box
    Refrigerant Charging Amount
    22 mm (0.866 in.)
    w/o Rear Cooler
    w/ Cool Box
    870 +/-30 g (30.7 +/-1.1 oz.)
    w/o Cool Box
    870 +/-30 g (30.7 +/-1.1 oz.)
    w/ Rear Cooler
    w/ Cool Box
    1010 +/-30 g (35.6 +/-1.1 oz.)
    w/o Cool Box
    960 +/-30 g (33.9 +/-1.1 oz.)
    16 mm (0.630 in.)
    w/o Rear Cooler
    w/ Cool Box
    770 +/-30 g (27.2 +/-1.1 oz.)
    w/o Cool Box
    770 +/-30 g (27.2 +/-1.1 oz.)
    w/ Rear Cooler
    w/ Cool Box
    970 +/-30 g (34.2 +/-1.1 oz.)
    w/o Cool Box
    920 +/-30 g (32.5 +/-1.1 oz.)

    I037365E19

    NOTICE:
    1. Do not operate the cooler compressor before charging refrigerant as the cooler compressor will not work properly without any refrigerant, and will overheat.
    2. Approximately 200 g (7.05 oz.) of refrigerant may need to be charged after bubbles disappear. The refrigerant amount should be checked by measuring its quantity, and not with the sight glass.


16. WARM UP ENGINE
  1. Warm up the engine at less than 1850 rpm for 2 minutes or more after charging the refrigerant.

    NOTICE:
    Be sure to warm up the compressor when turning the A/C switch is on after removing and installing the cooler refrigerant lines (including the compressor), to prevent damage to the compressor.


17. CHECK FOR REFRIGERANT GAS LEAK
  1. After recharging the refrigerant gas, check for refrigerant gas leakage using a halogen leak detector.

  1. Perform the operation under these conditions:

    1. Stop the engine.
    2. Secure good ventilation (the halogen leak detector may react to volatile gases other than refrigerant, such as evaporated gasoline or exhaust gas).
    3. Repeat the test 2 or 3 times.
    4. Make sure that some refrigerant remains in the refrigeration system. When compressor is off: approximately 392 to 588 kPa (4.0 to 6.0 kgf/cm2, 57 to 85 psi).

  1. I042222E21
    Using a halogen leak detector, check the refrigerant line for leakage.

  1. If a gas leak is not detected on the drain hose, remove the blower motor control (blower resistor) from the cooling unit. Insert the halogen leak detector sensor into the unit and perform the test.

  1. Disconnect the connector and wait for approximately 20 minutes. Bring the halogen leak detector close to the pressure switch and perform the test.

← REASSEMBLY (from Jan 2012)INSTALLATION (from Jan 2012) →