2011-2013 Land Cruiser · Service Manual Vehicle Interior

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


2. REMOVE REAR NO. 1 SEAT ASSEMBLY LH
  1. for 60/40 Split Seat Type 40 Side:
    Remove the rear No. 1 seat assembly (Click here).

  1. for 60/40 Split Seat Type 60 Side:
    Remove the rear No. 1 seat assembly (Click here).


3. REMOVE REAR NO. 1 SEAT ASSEMBLY RH
  1. for 60/40 Split Seat Type 40 Side:
    Remove the rear No. 1 seat assembly (Click here).

  1. for 60/40 Split Seat Type 60 Side:
    Remove the rear No. 1 seat assembly (Click here).


4. REMOVE REAR NO. 2 SEAT ASSEMBLY LH
  1. for Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).

  1. except Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).


5. REMOVE REAR NO. 2 SEAT ASSEMBLY RH
  1. for Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).

  1. except Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).


6. REMOVE REAR DOOR SCUFF PLATE LH
  1. w/ Sliding Roof:
    Remove the rear door scuff plate (Click here).

  1. w/o Sliding Roof:
    Remove the rear door scuff plate (Click here).


7. REMOVE REAR DOOR SCUFF PLATE RH
  1. w/ Sliding Roof:
    Remove the rear door scuff plate (Click here).

  1. w/o Sliding Roof:
    Remove the rear door scuff plate (Click here).


8. REMOVE REAR FLOOR MAT REAR SUPPORT PLATE
  1. w/ Sliding Roof:
    Remove the rear floor mat rear support plate (Click here).

  1. w/o Sliding Roof:
    Remove the rear floor mat rear support plate (Click here).


9. REMOVE TONNEAU COVER ASSEMBLY (w/ Tonneau Cover)
  1. Remove the tonneau cover.


10. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat)
  1. w/ Sliding Roof:
    Remove the rear seat cover cap (Click here).

  1. w/o Sliding Roof:
    Remove the rear seat cover cap (Click here).


11. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY LH
  1. w/ Sliding Roof:
    Remove the front quarter trim panel (Click here).

  1. w/o Sliding Roof:
    Remove the front quarter trim panel (Click here).


12. REMOVE REAR SEAT COVER CAP (w/ Rear No. 2 Seat)
  1. w/ Sliding Roof:
    Remove the rear seat cover cap (Click here).

  1. w/o Sliding Roof:
    Remove the rear seat cover cap (Click here).


13. REMOVE FRONT QUARTER TRIM PANEL ASSEMBLY RH
  1. w/ Sliding Roof:
    Remove the front quarter trim panel (Click here).

  1. w/o Sliding Roof:
    Remove the front quarter trim panel (Click here).


14. REMOVE REAR NO. 1 SEAT PROTECTOR

B184032E01
  1. Detach the 10 claws and remove the 2 seat protectors.


15. REMOVE REAR NO. 2 SEAT PROTECTOR

B184031E01
  1. Detach the 10 claws and remove the 2 seat protectors.


16. REMOVE FRONT FLOOR CARPET ASSEMBLY

E157065
  1. Fold back the floor carpet.

    HINT:
    Fold back the carpet until it is possible to remove the rear No. 6 air duct.


17. REMOVE REAR NO. 6 AIR DUCT
  1. Disconnect the 2 connectors.

  1. Remove the 5 screws and duct.

    E155886


18. REMOVE DUCT TEMPERATURE SENSOR

  1. Detach the 4 claws and remove the 2 sensors.

    E157078

← COMPONENTS (from Sep 2011)REMOVAL (from Jan 2012) →