2011-2013 Land Cruiser · Service Manual Suspension

REMOVAL

Removal / installation · Vehicles built from Sep 2011


1. REMOVE STABILIZER CONTROL VALVE PROTECTOR

C172095
  1. Detach the clamp, and disconnect the connector from the protector.

  1. Remove the 3 bolts and protector.


2. OPEN STABILIZER CONTROL WITH ACCUMULATOR HOUSING SHUTTER VALVE

  1. Using a 5 mm hexagon socket wrench, loosen the lower and upper chamber shutter valves of the stabilizer control with accumulator housing 2.0 to 3.5 turns.

    C175131E01

    NOTICE:
    1. When loosening a shutter valve, make sure that the end protrudes 2 to 3.5 mm (0.0787 to 0.137 in.) from the surface of the block, and do not turn the shutter valve any further.
    2. Do not remove the shutter valves.


3. REMOVE REAR WHEEL

4. REMOVE TAILPIPE ASSEMBLY
  1. for 2UZ-FE:
    Remove the tailpipe (Click here).

  1. for 1VD-FTV:
    Remove the tailpipe (Click here).


5. REMOVE EXHAUST CENTER PIPE ASSEMBLY
  1. for 2UZ-FE:
    Remove the center exhaust pipe (Click here).

  1. for 1VD-FTV:
    Remove the center exhaust pipe (Click here).


6. DISCHARGE SUSPENSION FLUID PRESSURE

C172270
  1. Connect the hose to the bleeder plug for the stabilizer control with accumulator housing and loosen the bleeder plug.

    CAUTION:
    Be careful as the vehicle height will rapidly decrease when the bleeder plug of the stabilizer control with accumulator housing is loosened.

  1. Discharge the suspension fluid from the stabilizer control with accumulator housing.

  1. After the fluid pressure has dropped and oil has drained out, tighten the bleeder plug and remove the hose.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }


7. SUPPORT REAR AXLE HOUSING ASSEMBLY

  1. C174050
    Support the rear axle housing with a jack using a wooden block to avoid damage.


8. REMOVE REAR STABILIZER END BRACKET

  1. C175234
    Remove the 2 bolts and disconnect the stabilizer end bracket.


9. REMOVE REAR STABILIZER BAR SUB-ASSEMBLY

  1. C178880
    Remove the nut and disconnect the stabilizer link from the stabilizer bar.

    NOTICE:
    Do not miss the ball joint dust cover protector.

    HINT:
    If the ball joint turns together with the nut, use a 6 mm hexagon wrench to hold the stud.

  1. C175231
    Remove the 4 bolts and stabilizer bar with the bushs and brackets.


10. REMOVE STABILIZER LINK SUB-ASSEMBLY

  1. C175254
    Remove the nut, 3 retainers and 2 cushions, and disconnect the stabilizer link from the bracket.

  1. C175253
    Remove the nut, bolt and stabilizer link.


11. REMOVE REAR STABILIZER CONTROL TUBE INSULATOR

  1. C174360
    Remove the 2 bolts and rear stabilizer control tube insulator.


12. REMOVE REAR STABILIZER CONTROL CYLINDER

  1. C175230E01
    Remove the 2 union bolts with the 2 gaskets and bolt, and disconnect the stabilizer control tube.

  1. Remove the bolt and stabilizer control cylinder.


13. REMOVE REAR NO. 2 STABILIZER LINK

  1. C175235
    Remove the 2 bolts, 2 nuts and No. 2 rear stabilizer link.


14. REMOVE REAR STABILIZER LINK ASSEMBLY

  1. C175236
    Remove the bolt, nut and rear stabilizer link.


15. REMOVE REAR SUSPENSION CONTROL BLEEDER PLUG

  1. C175252
    Remove the 2 rear suspension control bleeder plugs from the rear stabilizer control cylinder.

← COMPONENTS (from Sep 2011)INSPECTION (from Sep 2011) →