2011-2013 Land Cruiser · Service Manual Suspension

INSTALLATION

Removal / installation · Vehicles built from Sep 2011


1. INSTALL ACCELERATION SENSOR (for Driver Side)

  1. C172824
    Install the sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.


2. INSTALL ACCELERATION SENSOR (for Front Passenger Side)

  1. C172825
    Install the sensor with the bolt.

    Torque:
    8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

  1. Connect the connector.


3. INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK (for LHD)

  1. C178472E01
    Vehicle front side:

    1. Connect the 5 connectors.

  1. Vehicle rear side:

    1. Install the steering control ECU with junction block to the vehicle with the 2 bolts and nut .

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    2. Attach the 2 clamps.

    3. Connect the 7 connectors.


4. INSTALL STEERING CONTROL ECU WITH JUNCTION BLOCK (for RHD)

  1. C177318E01
    Vehicle front side:

    1. Connect the 3 connectors.

  1. Vehicle rear side:

    1. Install the steering control ECU with junction block to the vehicle with the bolt and 2 nuts.

      Torque:
      8.0 N*m{ 82 kgf*cm , 71 in.*lbf }

    2. Connect the 2 connectors.


5. INSTALL LOWER NO. 2 INSTRUMENT PANEL FINISH PANEL

B180304
  1. Connect the connector.

  1. Attach the 3 claws to install the lower No. 2 instrument panel finish panel.

  1. Install the 4 bolts.


6. INSTALL INSTRUMENT PANEL BOX DOOR KNOB

B182549
  1. Attach the 2 claws to install the instrument panel box door knob.


7. INSTALL NO. 3 INSTRUMENT CLUSTER FINISH PANEL GARNISH

B182550
  1. Attach the 6 claws to install the No. 3 instrument cluster finish panel garnish.


8. INSTALL LOWER INSTRUMENT PANEL (w/o Passenger Side Knee Airbag)

B180302
  1. Attach the 4 claws to install the lower instrument panel.

  1. Install the 2 bolts.


9. INSTALL FRONT PASSENGER SIDE KNEE AIRBAG ASSEMBLY (w/ Passenger Side Knee Airbag)

  1. B189607E01
    Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Attach the 4 claws to install the front passenger side knee airbag.

  1. Install the 4 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


10. INSTALL COWL SIDE TRIM BOARD RH

B180022
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the cap nut.


11. INSTALL NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B182552
  1. Attach the 4 claws to install the No. 2 instrument panel under cover.


12. INSTALL FRONT DOOR SCUFF PLATE RH

13. INSTALL INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)

B186358
  1. Connect the connector.

  1. Attach the 6 claws to install the instrument side panel.


14. INSTALL INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)

B182551
  1. Attach the 6 claws to install the instrument side panel.


15. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299
  1. Attach the 2 claws and connect the DLC3.

  1. Install the lower instrument panel with the 5 bolts.


16. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  1. B189604E01
    Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the driver side knee airbag with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


17. INSTALL NO. 1 SWITCH HOLE BASE

B180298
  1. Connect the connectors.

  1. Attach the 4 claws to install the No. 1 switch hole base.


18. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. B180296
    for Automatic Air Conditioning System:

    1. Attach the 2 claws to install the room temperature sensor.

  1. B181942
    Attach the 2 claws to connect the 2 control cables.

  1. w/ Driver Side Knee Airbag:

    1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

    2. Install the 2 bolts.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

    2. Install the 2 bolts.

      B291250

  1. B182569
    Attach the 2 claws to close the hole cover.


19. INSTALL COWL SIDE TRIM BOARD LH

B181911
  1. Attach the 2 clips to install the cowl side trim board.

  1. Install the cap nut.


20. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B182553
  1. Connect the connectors.

  1. Attach the 3 claws to install the No. 1 instrument panel under cover.

  1. Install the 2 screws.


21. INSTALL FRONT DOOR SCUFF PLATE LH

22. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

    B291252E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System


23. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E155133
  1. Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.


24. INSTALL INSTRUMENT SIDE PANEL LH

E155518
  1. Attach the 6 claws to install the instrument side panel.


25. INSTALL LOWER CENTER INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

  1. B180006
    Connect the connectors.

  1. Attach the 7 claws to install the panel.


26. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH

  1. B180005
    Attach the 7 claws to install the panel pad.

  1. Install the screw.

  1. Install the clip.


27. INSTALL NO. 1 INSTRUMENT PANEL FINISH PANEL CUSHION

  1. B182501
    Attach the 7 claws to install the panel cushion.


28. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

  1. B181910
    Connect the connectors and 2 clamps.

  1. Attach the 8 claws to install the panel pad.

  1. Install the screw.

  1. Install the clip.


29. INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

  1. E155134
    Attach the 7 claws to install the panel cushion.


30. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


31. CHECK SRS WARNING LIGHT
  1. Check the SRS warning light (Click here).

← INSPECTION (from Sep 2011)ON-VEHICLE INSPECTION (from Sep 2011) →