2011-2013 Land Cruiser · Service Manual Vehicle Interior

Heater Control Switch Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The temperature control switch assembly LH and RH sends the temperature up and down signal to the air conditioning amplifier assembly through the multi-display assembly*1 or the air conditioning control assembly*2.
  1. *1: w/ Navigation System
  2. *2: w/o Navigation System

WIRING DIAGRAM

E251613E03
B144127E05

INSPECTION PROCEDURE


1. CHECK VEHICLE TYPE
  1. Check if the vehicle is equipped with the navigation system.

    Result 
    Result
    Proceed to
    w/ Navigation System
    A
    w/o Navigation System
    B



B
Go to step 9
A


2. CHECK CAN COMMUNICATION SYSTEM
  1. Check the CAN communication system.

    OK:
    CAN communication system has no problem.

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
GO TO CAN COMMUNICATION SYSTEM (Click here)

C
GO TO CAN COMMUNICATION SYSTEM (Click here)
A


3. CHECK OPERATION
  1. Check that the temperature control switches operate.

    Result 
    Result
    Proceed to
    Temperature control switch LH does not operate
    A
    Temperature control switch RH does not operate
    B
    Temperature control switch LH and RH do not operate
    C



B
Go to step 6

C
Go to step 8
A


4. INSPECT TEMPERATURE CONTROL SWITCH ASSEMBLY LH

  1. E191987E01
    Remove the temperature control switch assembly LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (UP) - 4 (SE)
    UP switch pressed
    Below 1 Ω
    UP switch not pressed
    10 kΩ or higher
    5 (DOWN) - 4 (SE)
    DOWN switch pressed
    Below 1 Ω
    DOWN switch not pressed
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Temperature Control Switch Assembly LH)



NG
REPLACE TEMPERATURE CONTROL SWITCH ASSEMBLY LH (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (TEMPERATURE CONTROL SWITCH ASSEMBLY LH - MULTI-DISPLAY ASSEMBLY)
  1. Disconnect the F16 temperature control switch assembly LH connector.

  1. Disconnect the F90 multi-display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F16-3 (UP) - F90-2 (TEC+)
    Always
    Below 1 Ω
    F16-5 (DOWN) - F90-7 (TEC-)
    Always
    Below 1 Ω
    F16-4 (SE) - F90-6 (AGND)
    Always
    Below 1 Ω
    F16-3 (UP) - Body ground
    Always
    10 kΩ or higher
    F16-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    F16-4 (SE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTI-DISPLAY ASSEMBLY (Click here)

6. INSPECT TEMPERATURE CONTROL SWITCH ASSEMBLY RH

  1. E191987E02
    Remove the temperature control switch assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (UP) - 4 (SE)
    UP switch pressed
    Below 1 Ω
    UP switch not pressed
    10 kΩ or higher
    3 (DOWN) - 4 (SE)
    DOWN switch pressed
    Below 1 Ω
    DOWN switch not pressed
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Temperature Control Switch Assembly RH)



NG
REPLACE TEMPERATURE CONTROL SWITCH ASSEMBLY RH (Click here)
OK


7. CHECK HARNESS AND CONNECTOR (TEMPERATURE CONTROL SWITCH ASSEMBLY RH - MULTI-DISPLAY ASSEMBLY)
  1. Disconnect the F17 temperature control switch assembly RH connector.

  1. Disconnect the F90 multi-display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-5 (UP) - F90-3 (TES+)
    Always
    Below 1 Ω
    F17-3 (DOWN) - F90-8 (TES-)
    Always
    Below 1 Ω
    F17-4 (SE) - F90-9 (BGND)
    Always
    Below 1 Ω
    F17-5 (UP) - Body ground
    Always
    10 kΩ or higher
    F17-3 (DOWN) - Body ground
    Always
    10 kΩ or higher
    F17-4 (SE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTI-DISPLAY ASSEMBLY (Click here)

8. CHECK MULTI-DISPLAY ASSEMBLY
  1. Replace the multi-display assembly with a new or normally functioning one (Click here).

  1. Check that the temperature control with temperature control switch LH and RH.

    OK:
    Temperature control with temperature control switch LH and RH.



NG
PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)
OK

END (MULTI-DISPLAY ASSEMBLY IS DEFECTIVE)

9. CHECK LIN COMMUNICATION SYSTEM
  1. Check the LIN communication system.

    OK:
    LIN communication system has no problem.



NG
GO TO LIN COMMUNICATION SYSTEM (Click here)
OK


10. CHECK OPERATION
  1. Check that the temperature control switches operate.

    Result 
    Result
    Proceed to
    Temperature control switch LH does not operate
    A
    Temperature control switch RH does not operate
    B
    Temperature control switch LH and RH do not operate
    C



B
Go to step 13

C
Go to step 15
A


11. INSPECT TEMPERATURE CONTROL SWITCH ASSEMBLY LH

  1. E191987E01
    Remove the temperature control switch assembly LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    3 (UP) - 4 (SE)
    UP switch pressed
    Below 1 Ω
    UP switch not pressed
    10 kΩ or higher
    5 (DOWN) - 4 (SE)
    DOWN switch pressed
    Below 1 Ω
    DOWN switch not pressed
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Temperature Control Switch Assembly LH)



NG
REPLACE TEMPERATURE CONTROL SWITCH ASSEMBLY LH (Click here)
OK


12. CHECK HARNESS AND CONNECTOR (TEMPERATURE CONTROL SWITCH ASSEMBLY LH - AIR CONDITIONING CONTROL ASSEMBLY)
  1. Disconnect the F16 temperature control switch assembly LH connector.

  1. Disconnect the F10 air conditioning control assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F16-3 (UP) - F10-12 (DTP+)
    Always
    Below 1 Ω
    F16-5 (DOWN) - F10-11 (DTP-)
    Always
    Below 1 Ω
    F16-4 (SE) - F10-9 (S5)
    Always
    Below 1 Ω
    F16-3 (UP) - Body ground
    Always
    10 kΩ or higher
    F16-5 (DOWN) - Body ground
    Always
    10 kΩ or higher
    F16-4 (SE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY (Click here)

13. INSPECT TEMPERATURE CONTROL SWITCH ASSEMBLY RH

  1. E191987E03
    Remove the temperature control switch assembly RH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    5 (UP) - 4 (SE)
    UP switch pressed
    Below 1 Ω
    UP switch not pressed
    10 kΩ or higher
    3 (DOWN) - 4 (SE)
    DOWN switch pressed
    Below 1 Ω
    DOWN switch not pressed
    10 kΩ or higher

    Text in Illustration 
    *1
    Component without harness connected
    (Temperature Control Switch Assembly RH)



NG
REPLACE TEMPERATURE CONTROL SWITCH ASSEMBLY RH (Click here)
OK


14. CHECK HARNESS AND CONNECTOR (TEMPERATURE CONTROL SWITCH ASSEMBLY RH - AIR CONDITIONING CONTROL ASSEMBLY)
  1. Disconnect the F17 temperature control switch assembly RH connector.

  1. Disconnect the F10 air conditioning control assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F17-5 (UP) - F10-10 (PTP+)
    Always
    Below 1 Ω
    F17-3 (DOWN) - F10-3 (PTP-)
    Always
    Below 1 Ω
    F17-4 (SE) - F10-2 (SG)
    Always
    Below 1 Ω
    F17-5 (UP) - Body ground
    Always
    10 kΩ or higher
    F17-3 (DOWN) - Body ground
    Always
    10 kΩ or higher
    F17-4 (SE) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE AIR CONDITIONING CONTROL ASSEMBLY (Click here)

15. CHECK AIR CONDITIONING CONTROL ASSEMBLY
  1. Replace the air conditioning control assembly with a new or normally functioning one (Click here).

  1. Check that the temperature control with temperature control switch LH and RH.

    OK:
    Temperature control with temperature control switch LH and RH.



NG
REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)
OK

END (AIR CONDITIONING CONTROL ASSEMBLY IS DEFECTIVE)


← Heater Control Switch Circuit (Sep 2011 – Dec 2011)Air Conditioning Compressor Magnetic Clutch Circuit (Sep 2011 – Dec 2011) →