2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

U0235 Lost Communication with Cruise Control Front Distance Range Sensor

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

The distance control ECU sends general vehicle control information, such as vehicle speed, steering angle, etc., to the millimeter wave radar sensor. The millimeter wave radar sensor sends information about whether another vehicle is present in front of the vehicle, the distance between the vehicles, relative speed, etc. to the distance control ECU. The distance control ECU sends this information to the ECM and performs control of cruise control.
DTC Code
DTC Detection Condition
Trouble Area
U0235
The vehicle speed is 50 km/h (30 mph) or more with the cruise control main switch on (vehicle-to-vehicle distance control mode) and the data sent from the millimeter wave radar sensor to the distance control ECU is abnormal.
  1. Millimeter wave radar sensor
  2. Distance control ECU
  3. Harness or connector
  4. CAN communication system

WIRING DIAGRAM

E149026E02

INSPECTION PROCEDURE

NOTICE:
  1. When the distance control ECU is replaced with a new one, initialization must be performed (Click here).
  2. When the millimeter wave radar sensor is replaced with a new one, adjustment of the radar sensor beam axis must be performed (Click here).
  3. As it is possible that this DTC was stored due to a bad connection of a connector, make sure to check that each connector is connected securely.


1. CHECK HARNESS AND CONNECTOR (MILLIMETER WAVE RADAR SENSOR - DISTANCE CONTROL ECU AND BODY GROUND)

  1. E149027E05
    Disconnect the A56 millimeter wave radar sensor connector.

  1. Disconnect the E108 distance control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A56-3 (LRDD) - E108-22 (LRDD)
    Always
    Below 1 Ω
    A56-5 (IGB) - E108-13 (IGB)
    E108-12 (GND) - Body ground
    E108-22 (LRDD) - Body ground
    Always
    10 kΩ or higher
    E108-13 (IGB) - Body ground
    A56-2 (SGND) - Body ground
    Always
    10 kΩ or higher
    E108-10 (SGND) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK DISTANCE CONTROL ECU

  1. E149028E02
    Disconnect the A56 millimeter wave radar sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E108-13 (IGB) - E108-10 (SGND)
    Engine switch on (IG)
    11 to 14 V
    E108-22 (LRDD) - E108-10 (SGND)
    4.5 to 5.5 V



NG
REPLACE DISTANCE CONTROL ECU (Click here)
OK


3. REPLACE MILLIMETER WAVE RADAR SENSOR
  1. Replace the millimeter wave radar sensor with a new one (Click here).

  1. Adjust the millimeter wave radar sensor (Click here).


NEXT


4. CHECK DTC (DYNAMIC RADAR CRUISE CONTROL SYSTEM)
  1. Using the intelligent tester, enter the following menus: Powertrain / Radar Cruise / Trouble Code.

  1. Clear the DTCs (Click here).

  1. Perform the following to make sure the DTC detection conditions are met.

    HINT:
    If the detection conditions are not met, the system cannot detect the malfunction.

    1. Drive the vehicle at a speed of 50 km/h (30 mph) or more.

    2. Turn the cruise control main switch on.

    3. Push the -SET switch to activate the dynamic radar cruise control.

  1. Check for DTCs (Click here).

    OK:
    DTC U0235 is not output.



NG
REPLACE DISTANCE CONTROL ECU (Click here)
OK

END (MILLIMETER WAVE RADAR SENSOR IS DEFECTIVE)


← U0100 Communication Stop from ECM to Distance Control ECU, VSC (+ U0122, U0123, U0126, U1101) (from Jan 2012)U1102 Lost Communication with Radar Sensor (from Jan 2012) →