2011-2013 Land Cruiser · Service Manual Vehicle Exterior

INSPECTION

Inspection · Vehicles built from Jan 2012


INSPECT BACK DOOR REMOTE CONTROL ASSEMBLY

B231790E01
  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Back door remote control is pulled (on)
    Below 1 Ω
    1 - 2
    Back door remote control is not pulled (off)
    10 kΩ or higher

    If the result is not as specified, replace the back door remote control assembly.
    Text in Illustration 
    *a
    Component without harness connected
    (Back Door Remote Control Assembly)
    *b
    Not pulled (off)
    *c
    Pulled (on)


INSPECT LOWER TAIL GATE LOCK ASSEMBLY LH

  1. E163334E12
    Operation check:

    1. Set the lower tail gate lock LH to the full-latch position.

    2. Apply battery voltage and check operation of the lower tail gate lock motor LH.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (ACT-)
      Battery negative (-) → Terminal 5 (ACT+)
      Latch turns to open-latch position

      If the result is not as specified, replace the lower tail gate lock assembly LH.

    3. Set the lower tail gate lock LH to the half-latch position.

    4. Apply battery voltage and check operation of the lower tail gate lock motor LH.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 5 (ACT+)
      Battery negative (-) → Terminal 6 (ACT-)
      Latch turns to over-latch position

      If the result is not as specified, replace the lower tail gate lock assembly LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Lower Tail Gate Lock Assembly LH)
      *b
      Over-latch
      *c
      Full-latch
      *d
      Half-latch
      *e
      Open-latch

  1. E163334E13
    Resistance check:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Close Position Switch 
      Tester Connection
      Condition
      Specified Condition
      7 (HND) - 8 (GND)
      Over-latch
      Below 1 Ω
      7 (HND) - 8 (GND)
      Full-latch
      10 kΩ or higher
      7 (HND) - 8 (GND)
      Half-latch
      10 kΩ or higher
      7 (HND) - 8 (GND)
      Open-latch
      10 kΩ or higher

      If the result is not as specified, replace the lower tail gate lock assembly LH.

      Lower Tail Gate Courtesy Switch:
      Tester Connection
      Condition
      Specified Condition
      2 (FUL) - 3 (E1)
      Over-latch
      10 kΩ or higher
      2 (FUL) - 3 (E1)
      Full-latch
      10 kΩ or higher
      2 (FUL) - 3 (E1)
      Half-latch
      Below 1 Ω
      2 (FUL) - 3 (E1)
      Open-latch
      Below 1 Ω

      If the result is not as specified, replace the lower tail gate lock assembly LH.

      Half-latch Switch:
      Tester Connection
      Condition
      Specified Condition
      1 (HAF) - 3 (E1)
      Over-latch
      10 kΩ or higher
      1 (HAF) - 3 (E1)
      Full-latch
      Below 1 Ω
      1 (HAF) - 3 (E1)
      Half-latch
      10 kΩ or higher
      1 (HAF) - 3 (E1)
      Open-latch
      Below 1 Ω

      If the result is not as specified, replace the lower tail gate lock assembly LH.

      Pawl Switch:
      Tester Connection
      Condition
      Specified Condition
      4 (POL) - 3 (E1)
      Over-latch
      10 kΩ or higher
      4 (POL) - 3 (E1)
      Full-latch
      Below 1 Ω
      4 (POL) - 3 (E1)
      Half-latch
      Below 1 Ω
      4 (POL) - 3 (E1)
      Open-latch
      10 kΩ or higher

      If the result is not as specified, replace the lower tail gate lock assembly LH.
      Text in Illustration 
      *a
      Component without harness connected
      (Lower Tail Gate Lock Assembly LH)
      *b
      Over-latch
      *c
      Full-latch
      *d
      Half-latch
      *e
      Open-latch


INSPECT LOWER TAIL GATE LOCK ASSEMBLY RH

  1. E163615E07
    Operation check:

    1. Set the lower tail gate lock RH to the full-latch position.

    2. Apply battery voltage and check operation of the lower tail gate lock motor RH.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 6 (ACT-)
      Battery negative (-) → Terminal 5 (ACT+)
      Latch turns to open-latch position

      If the result is not as specified, replace the lower tail gate lock assembly RH.

    3. Set the lower tail gate lock RH to the half-latch position.

    4. Apply battery voltage and check operation of the lower tail gate lock motor RH.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → Terminal 5 (ACT+)
      Battery negative (-) → Terminal 6 (ACT-)
      Latch turns to over-latch position

      If the result is not as specified, replace the lower tail gate lock assembly RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Lower Tail Gate Lock Assembly RH)
      *b
      Over-latch
      *c
      Full-latch
      *d
      Half-latch
      *e
      Open-latch

  1. E163615E08
    Resistance check:

    1. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Close Position Switch 
      Tester Connection
      Condition
      Specified Condition
      7 (HND) - 8 (GND)
      Over-latch
      Below 1 Ω
      7 (HND) - 8 (GND)
      Full-latch
      10 kΩ or higher
      7 (HND) - 8 (GND)
      Half-latch
      10 kΩ or higher
      7 (HND) - 8 (GND)
      Open-latch
      10 kΩ or higher

      If the result is not as specified, replace the lower tail gate lock assembly RH.

      Lower Tail Gate Courtesy Switch:
      Tester Connection
      Condition
      Specified Condition
      2 (FUL) - 3 (E1)
      Over-latch
      10 kΩ or higher
      2 (FUL) - 3 (E1)
      Full-latch
      10 kΩ or higher
      2 (FUL) - 3 (E1)
      Half-latch
      Below 1 Ω
      2 (FUL) - 3 (E1)
      Open-latch
      Below 1 Ω

      If the result is not as specified, replace the lower tail gate lock assembly RH.

      Half-latch Switch:
      Tester Connection
      Condition
      Specified Condition
      1 (HAF) - 3 (E1)
      Over-latch
      10 kΩ or higher
      1 (HAF) - 3 (E1)
      Full-latch
      Below 1 Ω
      1 (HAF) - 3 (E1)
      Half-latch
      10 kΩ or higher
      1 (HAF) - 3 (E1)
      Open-latch
      Below 1 Ω

      If the result is not as specified, replace the lower tail gate lock assembly RH.

      Pawl Switch:
      Tester Connection
      Condition
      Specified Condition
      4 (POL) - 3 (E1)
      Over-latch
      10 kΩ or higher
      4 (POL) - 3 (E1)
      Full-latch
      Below 1 Ω
      4 (POL) - 3 (E1)
      Half-latch
      Below 1 Ω
      4 (POL) - 3 (E1)
      Open-latch
      10 kΩ or higher

      If the result is not as specified, replace the lower tail gate lock assembly RH.
      Text in Illustration 
      *a
      Component without harness connected
      (Lower Tail Gate Lock Assembly RH)
      *b
      Over-latch
      *c
      Full-latch
      *d
      Half-latch
      *e
      Open-latch

← DISASSEMBLY (from Jan 2012)ADJUSTMENT (Sep 2011 – Dec 2011) →