2011-2013 Land Cruiser · Service Manual Vehicle Exterior

ADJUSTMENT

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSPECT TAIL GATE PANEL SUB-ASSEMBLY

  1. Check that the clearance measurements of areas H to I are within the standard range.

    B189146E01

    Standard Measurement:
    Area
    Specified Condition
    H
    3.8 to 6.8 mm (0.150 to 0.268 in.)
    I
    3.5 to 6.5 mm (0.138 to 0.256 in.)


2. ADJUST TAIL GATE PANEL SUB-ASSEMBLY
  1. Loosen the hinge bolts.

  1. B181348
    Adjust the tail gate by moving it up and down and left and right so that the dimensions are within the specified range.

  1. Tighten the hinge bolts.

    Torque:
    28 N*m{ 286 kgf*cm , 21 ft.*lbf }

  1. B181347
    Loosen the hinge bolts.

  1. Adjust the tail gate by moving it up and down and forward and backward so that the dimensions are within the specified range.

  1. Tighten the hinge bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }


3. ADJUST DOOR LOCK STRIKER

  1. B181355
    Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

  1. Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


4. INSPECT BACK DOOR PANEL SUB-ASSEMBLY

  1. Check that the clearance measurements of areas A to G are within the standard range.

    B182258E01

    Standard Measurement:
    Area
    Specified Condition
    Area
    Specified Condition
    A
    5.7 to 8.7 mm (0.224 to 0.343 in.)
    E
    2.7 to 5.7 mm (0.106 to 0.224 in.)
    B
    0.0 to 3.0 mm (0.000 to 0.118 in.)
    F
    -1.4 to 1.6 mm (-0.0551 to 0.0630 in.)
    C
    3.75 to 6.75 mm (0.148 to 0.266 in.)
    G
    5.0 mm (0.197 in.)
    D
    3.75 to 6.75 mm (0.148 to 0.266 in.)
    -
    -


5. ADJUST REAR SWING GATE LOCK STRIKER

  1. B181346
    Check that the door fit and door linkages are adjusted correctly.

  1. Using a T40 "TORX" socket, adjust the striker position by slightly loosening the striker mounting screws and hitting the striker with a plastic-faced hammer.

  1. Using a T40 "TORX" socket, tighten the striker mounting screws after the adjustment.

    Torque:
    12 N*m{ 122 kgf*cm , 9 ft.*lbf }


6. ADJUST BACK DOOR PANEL SUB-ASSEMBLY

  1. B181344
    Loosen the hinge bolts.

  1. Adjust the back door by moving it up and down and left and right so that the dimensions are within the specified range.

  1. Tighten the hinge bolts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Partially remove the roof headlining.

    1. w/ Sliding Roof:
      (Click here)

    2. w/o Sliding Roof:
      (Click here)

  1. B189860
    Loosen the hinge nuts.

  1. Adjust the back door by moving it up and down and forward and backward so that the dimensions are within the specified range.

  1. Tighten the hinge nuts.

    Torque:
    19 N*m{ 194 kgf*cm , 14 ft.*lbf }

  1. Install the roof headlining.

    1. w/ Sliding Roof:
      (Click here)

    2. w/o Sliding Roof:
      (Click here)

← INSPECTION (from Jan 2012)ADJUSTMENT (from Jan 2012) →