2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B15D5 Rear Seat Entertainment System Disconnected

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

The television display assembly and multi-media module receiver assembly are connected by a MOST network.
When a MOST network error occurs between the display module board and multi-display assembly, these DTCs will be stored.
DTC Code
DTC Detection Condition
Trouble Area
B15D5*
A device that is listed in the MOST network connected device record of the master unit is missing.
  1. Television display assembly power source circuit
  2. MOST network
  3. Multi-display assembly
  4. Multi-media module receiver assembly

HINT:
  1. *: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
  2. The multi-media module receiver assembly is the master unit.


WIRING DIAGRAM

E248578E01

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


2. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
Go to step 3
OK

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY - BATTERY AND BODY GROUND)

  1. E245657E03
    Disconnect the television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L53-3 (GND) - Body ground
    Always
    Below 1 Ω
    L53-4 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L53-1 (+B) - Body ground
    Always
    11 to 14 V
    L53-11 (+B2) - Body ground
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Television Display Assembly)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY)
  1. Disconnect the F84 multi-media module receiver assembly connector.

  1. Disconnect the L56 television display assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F84-2 (MI+) - L56-5 (MO+)
    Always
    Below 1 Ω
    F84-3 (MI-) - L56-6 (MO-)
    Always
    Below 1 Ω
    F84-4 (SLDI) - L56-7 (SLDO)
    Always
    Below 1 Ω
    F84-2 (MI+) - Body ground
    Always
    10 kΩ or higher
    F84-3 (MI-) - Body ground
    Always
    10 kΩ or higher
    F84-4 (SLDI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE TELEVISION DISPLAY ASSEMBLY
  1. Replace the television display assembly with a new or normally functioning one (Click here).


NEXT


6. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


7. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK

END (TELEVISION DISPLAY ASSEMBLY IS DEFECTIVE)


← B15B0 Display Screen Malfunction (from Jan 2012)A Remote Control System does not Operate (Sep 2011 – Dec 2011) →