B1591 No Response from Audio HU
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Also covers:
- B15D1 Audio HU Disconnected
DESCRIPTION
The display and navigation module display and radio receiver assembly are connected by the MOST communication line.When an MOST communication error occurs between the display and navigation module display and the radio receiver assembly, these DTCs will be stored.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| B1591 |
Within the time-out period, there was no response from the radio receiver assembly to the following requests from the master unit:
|
|
| B15D1*1 |
When either of the conditions below is met:
|
- HINT:
- *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
- The display and navigation module display is the master unit.
- *1: Even if no fault is present, this DTC may be stored depending on the battery condition or engine start voltage.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
| 1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
Check for optional components.
Check that optional components (including associated wiring) which generate radio waves are not installed.
Result Result
Proceed to
Optional components (including associated wiring) are installed.
A
Optional components (including associated wiring) are not installed.
B
- HINT:
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.
- This DTC may be stored when an MOST communication error occurs due to electrical noise.
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.
|
|
||||
| A | |
| 2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
Remove optional components (including associated wiring).
- NOTICE:
- Do not remove optional components or associated wiring without the permission of the customer.
| NEXT | |
| 3. CHECK DTC |
Clear the DTCs (Click here).
Recheck for DTCs and check if the same trouble occurs again.
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
| 4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER ASSEMBLY POWER SOURCE) |
Disconnect the F56 radio receiver assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F56-15 (GND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
F56-14 (B) - F56-15 (GND)
Always
11 to 14 V
Text in Illustration *1
Front view of wire harness connector
(to Radio Receiver Assembly)
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - RADIO RECEIVER) |
Disconnect the F65 display and navigation module display connector.
Disconnect the F56 radio receiver assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F65-3 (MO+) - F56-9 (MI+)
Always
Below 1 Ω
F65-7 (MO-) - F56-23 (MI-)
Always
Below 1 Ω
F65-6 (SLDO) - F56-10 (SLDI)
Always
Below 1 Ω
F65-3 (MO+) - Body ground
Always
10 kΩ or higher
F65-7 (MO-) - Body ground
Always
10 kΩ or higher
F65-6 (SLDO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - STEREO COMPONENT AMPLIFIER) |
Disconnect the F56 radio receiver assembly connector.
Disconnect the F59 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F56-11 (MO+) - F59-4 (MI+)
Always
Below 1 Ω
F56-25 (MO-) - F59-10 (MI-)
Always
Below 1 Ω
F56-24 (SLDI) - F59-5 (SLDI)
Always
Below 1 Ω
F56-11 (MO+) - Body ground
Always
10 kΩ or higher
F56-25 (MO-) - Body ground
Always
10 kΩ or higher
F56-24 (SLDI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. REPLACE RADIO RECEIVER ASSEMBLY |
Replace the radio receiver assembly (Click here).
Clear the DTCs (Click here).
Recheck for DTCs and check if the same trouble occurs again.
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
