DIAGNOSIS SYSTEM
Troubleshooting · Vehicles built from Jan 2012
| WIDE VIEW FRONT MONITOR SYSTEM |
For wide view front monitor system diagnosis, signals received by the parking assist ECU can be checked and the wide view front monitor system can be calibrated, adjusted and checked using the multi-display assembly.
- NOTICE:
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the wide view front monitor system may be needed (Click here).
- HINT:
- The displayed screens and items may differ depending on vehicle specifications.
| DIAGNOSIS SCREEN TRANSITION (during parking assist ECU initialization) |




| DIAGNOSIS SCREEN TRANSITION (after parking assist ECU initialization) |




| DIAGNOSTIC MODE |
Start diagnostic mode (Click here).
Failure diagnosis (Click here).
System check (check using system check mode screen) (Click here).

Finish diagnostic mode (Click here).
| SIGNAL CHECK (parking assist ECU input signal) |
Start diagnostic mode (Click here).
Select "Function Check/Setting" on the [Service Menu screen] to display the Function Check/Setting screen.

Select "Camera Setting" on the [Function Check/Setting] screen.

- HINT:
- After "Camera Setting" is selected, the screen transitions differ depending on whether initialization of the parking assist ECU was performed after parking assist ECU replacement.
Parking Assist ECU Initialization
Screen Transition
Not performed
[Signal Check] screen
Performed
[Mode Setting] screen
When the screen changes to the [Mode Setting] screen, select "Back Camera Setting" to display the [Signal Check] screen.

- HINT:
- To select a grayed out item, select and hold the item for 2 seconds or more.
Signal Check:

On the [Signal Check] screen, it is possible to inspect the state of signals sent to the parking assist ECU and check the settings.
Item
Inspection Detail
Note
CAN
Speed signal input
When "CHK" (red) is displayed, selecting "Next" will not change to the next screen.
CAMERA SW
Front and side monitor main switch signal input
MIRROR SW
Outer rear view mirror retract signal input
VGRS*
VGRS signal input
D-CAM SET
Driver side camera information signal input
-
OTA
Off-road turn assist function information input
-
DEST
Destination code signal input
-
- *: w/ Variable Gear Ratio Steering System
- HINT:
- When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.
- If performing the adjustment after proceeding to the next screen, confirm that all items display "OK" (blue) before selecting "Next".
- When "CHK" (red) is displayed, perform inspections based on the result of the following inspections.
- *: w/ Variable Gear Ratio Steering System
CAN inspection:
- HINT:
- If "CHK" (red) is displayed for "CAN", check for DTCs and perform troubleshooting based on the output DTCs (Click here).
CAMERA SW inspection:
Check that "OK" (blue) is displayed for "CAMERA SW" and select "OK".
Check that "OK" (blue) changes to "CHK" (red). Press the front and side monitor main switch (steering pad switch assembly) and check that "CHK" (red) returns to "OK" (blue).
- HINT:
- If "CHK" (red) remains displayed or the "CAMERA SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the [Signal Check] screen) (Click here).
MIRROR SW inspection:
Check that "OK" (blue) is displayed for "MIRROR SW" and select "OK".
Check that "OK" (blue) changes to "CHK" (red). Press the outer mirror switch and check that "CHK" (red) returns to "OK" (blue).
- HINT:
- After operating the outer mirror retract switch, if the outer mirror remains in the retracted state, return the outer mirror to the driving position. If "CHK" (red) remains displayed or the "MIRROR SW" inspection result is not normal, perform troubleshooting according to Problem Symptoms Table ("CHK" message(s) are displayed on the [Signal Check] screen) (Click here)
VGRS inspection (w/ Variable Gear Ratio Steering System):
- HINT:
- If "CHK" (red) is displayed for "VGRS", check for DTCs and perform troubleshooting based on the output DTCs (Click here).
D-CAM SET inspection:
Check that "WITH" (blue) is displayed for "D-CAM SET".
OTA inspection:
Check that displayed for "OTA" is matched off-road turn assist function for vehicles.
DEST inspection:
Check that displayed for "DEST" is matched destination code for vehicles.
Finish diagnostic mode (Click here).
| CALIBRATION WHEN SERVICING VEHICLE |
- NOTICE:
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the wide view front monitor system may be needed (Click here).