"CHK" message(s) are displayed on the SIGNAL CHECK screen.
Circuit diagnosis · Vehicles built from Jan 2012
DESCRIPTION
On the [Signal Check] screen, it is possible to check if the state of signals sent to the parking assist ECU is normal (Click here).- HINT:
- On the [Signal Check] screen, "OK" (blue) is displayed for items with a normal inspection result and input state.
- On the [Signal Check] screen, "CHK" (red) is displayed for items with an abnormal inspection result and input state.
- Displayed items may differ depending on the specifications.
- On the [Signal Check] screen, "OK" (blue) is displayed for items with a normal inspection result and input state.
| Item |
Signal Input Method |
Detail |
DTC Output when Abnormal Result is Displayed |
| CAN |
CAN communication |
Speed signal input |
DTC is output |
| CAMERA SW |
Vehicle wire harness |
Front and side monitor main switch signal input |
DTC is not output |
| MIRROR SW |
Vehicle wire harness |
Outer rear view mirror retract signal input |
DTC is not output |
| VGRS |
CAN communication |
VGRS signal input |
DTC is output |
| D-CAM SET |
Vehicle wire harness |
Driver side camera information signal input |
DTC is not output |
| OTA |
Vehicle wire harness |
Off-road turn assist function information signal input |
DTC is not output |
| DEST |
Vehicle wire harness |
Destination code signal input |
DTC is not output |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When "System initializing" is displayed on the display and navigation module display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (Click here).
- Inspect the fuses for circuits related to this system before performing the following inspection procedure.
- When "System initializing" is displayed on the display and navigation module display after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
| 1. CHECK DISPLAY CHECK MODE |
Check which items display "CHK" (red) on the [Signal Check] screen.

Result Result
Proceed to
"CAMERA SW" and "WFS SET" displays "CHK" (red).
A
"MIRROR SW" displays "CHK" (red).
B
"VGRS" displays "CHK" (red).
C
"CAN" displays "CHK" (red).
D
|
|
||||
|
|
||||
| A | |
| 2. INSPECT FRONT AND SIDE MONITOR MAIN SWITCH ASSEMBLY |
Remove the front and side monitor main switch assembly (Click here).
Inspect the front and side monitor main switch assembly (Click here).
|
|
||||
| OK | |
| 3. CHECK HARNESS AND CONNECTOR (FRONT AND SIDE MONITOR MAIN SWITCH ASSEMBLY - PARKING ASSIST ECU, BATTERY AND BODY GROUND) |
Disconnect the G15 front and side monitor main switch assembly connector.
Disconnect the F76 parking assist ECU assembly connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
G15-6 (IG) - Body ground
Engine switch on (IG)
11 to 14 V
G15-6 (IG) - Body ground
Engine switch off
Below 1 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F76-7 (BLSW) - G15-9(ECU)
Always
Below 1 Ω
G15-9 (ECU) - Body ground
Always
10 kΩ or higher
G15-6 (IG) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
| 4. INSPECT OUTER MIRROR SWITCH ASSEMBLY |
Remove the outer mirror switch assembly (Click here).
Inspect the outer mirror switch assembly (Click here).
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (OUTER MIRROR SWITCH ASSEMBLY - PARKING ASSIST ECU) |
Disconnect the F75 parking assist ECU connector.
Disconnect the G16 outer mirror switch assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F75-5 (MPOS) - G16-6 (MR)
Always
Below 1 Ω
F75-5 (MPOS) - Body ground
Always
10 kΩ or higher
G16-5 (E) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 6. CHECK POWER MIRROR CONTROL SYSTEM (POWER RETRACT FUNCTION) |
Check the power mirror control system (power retract function) (See page ).
- OK:
- Power mirror control system (power retract function) is normal.
|
|
||||
| OK | ||
| ||
