C1683 Side Camera Feedback Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- C1684 Side Camera Current Malfunction
DESCRIPTION
DTC C1683 is stored if the parking assist ECU judges as a result of its self check that a synchronization problem is occurring in the image signal sent from the side television camera assembly (for Front Passenger Side) to the parking assist ECU.DTC C1684 is stored if the parking assist ECU judges as a result of its self check that there is a problem with the current supplied from the side television camera assembly (for Front Passenger Side) connected to the parking assist ECU.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1683 |
Side Camera Feedback Malfunction |
|
| C1684 |
Side Camera Current Malfunction |
WIRING DIAGRAM




INSPECTION PROCEDURE
- NOTICE:
- When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the side monitor system may be needed (Click here).
- When "System initializing" is displayed on the parking assist ECU after the cable is disconnected from the negative (-) battery terminal, correct the steering angle neutral point (Click here).
| 1. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - OUTER REAR VIEW MIRROR ASSEMBLY AND BODY GROUND) |
Disconnect the F75 and F76 parking assist ECU connectors.
Disconnect the I32*1 or I35*2 outer rear view mirror assembly (for Front Passenger Side) connector.
- *1: for LHD
- *2: for RHD
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
- for LHD:
Tester Connection
Condition
Specified Condition
F76-34 (SCV-) - I32-12 (SCV-)
Always
Below 1 Ω
F76-10 (SCV+) - I32-1 (SCV+)
Always
Below 1 Ω
F76-33 (SGND) - I32-13 (SGND)
Always
Below 1 Ω
F76-32 (SCB+) - I32-2 (SCB+)
Always
Below 1 Ω
F75-4 (GND1) - Body ground
Always
Below 1 Ω
F76-34 (SCV-) - Body ground
Always
10 kΩ or higher
F76-10 (SCV+) - Body ground
Always
10 kΩ or higher
F76-33 (SGND) - Body ground
Always
10 kΩ or higher
F76-32 (SCB+) - Body ground
Always
10 kΩ or higher
- for RHD:
Tester Connection
Condition
Specified Condition
F76-34 (SCV-) - I35-12 (DCV-)
Always
Below 1 Ω
F76-10 (SCV+) - I35-1 (DCV+)
Always
Below 1 Ω
F76-33 (SGND) - I35-13 (DGND)
Always
Below 1 Ω
F76-32 (SCB+) - I35-2 (DCB+)
Always
Below 1 Ω
F75-4 (GND1) - Body ground
Always
Below 1 Ω
F76-34 (SCV-) - Body ground
Always
10 kΩ or higher
F76-10 (SCV+) - Body ground
Always
10 kΩ or higher
F76-33 (SGND) - Body ground
Always
10 kΩ or higher
F76-32 (SCB+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. CHECK PARKING ASSIST ECU (SCB+, SGND) |
Reconnect the F75 and F76 parking assist ECU connectors.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
F76-33 (SGND) - Body ground
Always
Below 1 Ω
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F76-32 (SCB+) - F76-33 (SGND)
Engine switch on (IG), front and side monitor main switch assembly on
5.5 to 7.05 V
| *a |
Component with harness connected (Parking Assist ECU) |
|
|
||||
| OK | |
| 3. CHECK SIDE TELEVISION CAMERA ASSEMBLY (SCV+, SGND OR DCV+, DGND) |
Reconnect the I32*1 or I35*2 outer rear view mirror assembly (for Front Passenger Side) connector.
- *1: for LHD
- *2: for RHD


Text in Illustration *a
Component with harness connected
(Parking Assist ECU)
*b
Waveform A
*c
Waveform B
*d
Synchronization Signal
*e
Video Waveform
-
-
- HINT:
- A waterproof connector is used for the side television camera assembly (for Front Passenger Side). Therefore, inspect the waveform at the parking assist ECU with the connector connected.
- The video waveform changes according to the image sent by the side television camera assembly (for Front Passenger Side).
- A waterproof connector is used for the side television camera assembly (for Front Passenger Side). Therefore, inspect the waveform at the parking assist ECU with the connector connected.
- *1: for LHD
Measure the resistance according to the value(s) in the table below.
- OK:
- Waveform is as shown in the illustration.
Item
Content
Terminal No. (Symbol)
F76-10 (SCV+) - F76-33 (SGND)
Tool Setting
200 mV/DIV., 50 μsec./DIV.
Condition
- Waveform A: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is not covered, displaying an image
- Waveform B: Engine switch on (IG), front and side monitor main switch assembly on and camera lens is covered, blacking out the screen
|
|
||||
| OK | ||
| ||
| 4. REPLACE SIDE TELEVISION CAMERA ASSEMBLY |
Replace the side television camera assembly (for Front Passenger Side) with a new or normally functioning one (Click here).
| NEXT | |
| 5. CHECK FOR DTC |
Clear the DTCs (Click here).
Check for DTCs (Click here).
- OK:
- DTC C1683 or C1684 is not output.
|
|
||||
| OK | ||
| ||
