2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B15D8 Monitor Disconnected

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The display and navigation module display and parking assist ECU are connected by the AVC-LAN communication line.
When an AVC-LAN communication error occurs between the display and navigation module display and parking assist ECU, this DTC will be stored.
DTC No.
DTC Detection Condition
Trouble Area
B15D8
A device that is listed in the AVC-LAN connected device record of the master unit is missing.
  1. Parking assist ECU power source circuit
  2. AVC-LAN circuit between display and navigation module display and parking assist ECU
  3. Parking assist ECU
  4. Display and navigation module display

HINT:
The display and navigation module display is the master unit.


WIRING DIAGRAM

E176692E12

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
      2. This DTC may be stored when an AVC-LAN communication error occurs due to electrical noise.



B
Go to step 3
A


2. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
Go to step 4
OK

END

4. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU POWER SOURCE)

  1. E195626E03
    Disconnect the F43 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F43-4 (GND1) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F43-6 (+B) - F43-4 (GND1)
    Always
    11 to 14 V
    F43-1 (IG) - F43-4 (GND1)
    Engine switch on (IG)
    11 to 14 V
    F43-14 (ACC) - F43-4 (GND1)
    Engine switch on (ACC)
    11 to 14 V

Text in Illustration 
*1
Front view of wire harness connector
(to Parking Assist ECU)


NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - DISPLAY AND NAVIGATION MODULE DISPLAY)
  1. Disconnect the F43 parking assist ECU connector.

  1. Disconnect the F66 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F43-31 (TX+) - F66-1 (TX1+)
    Always
    Below 1 Ω
    F43-32 (TX-) - F66-2 (TX1-)
    Always
    Below 1 Ω
    F43-31 (TX+) - Body ground
    Always
    10 kΩ or higher
    F43-32 (TX-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. REPLACE PARKING ASSIST ECU
  1. Replace the parking assist ECU (Click here).

  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)
OK

END


← B15D0 MOST Communication Malfunction (Sep 2011 – Dec 2011)B15F5 A/C ECU Vehicle Information Reading/Writing Processor Malfunction (Sep 2011 – Dec 2011) →