2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B15D0 MOST Communication Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

This DTC is stored when the MOST network cannot be established after the master unit is activated.
DTC No.
DTC Detection Condition
Trouble Area
B15D0
MOST network cannot be established.
  1. MOST line check
  2. MOST communication line connector
  3. Wire harness or connector
  4. MOST communication line
  5. Radio receiver assembly
  6. Stereo component amplifier assembly
  7. Television display assembly (w/ Rear Seat Entertainment System)
  8. Display and navigation module display

HINT:
  1. For the MOST network, the display and navigation module display is the master unit.
  2. Errors may occur in MOST communication between devices due to problems such as electrical noise.


WIRING DIAGRAM

E194867E02
E194868E02

INSPECTION PROCEDURE


1. PERFORM MOST LINE CHECK

  1. E194869E01
    Display the "MOST Line Check" screen (Click here).

  1. Check the result on the "MOST Line Check" screen.

    Result 
    Result
    Proceed to
    "NCON" is displayed for "AUDIO".
    A
    "NCON" is displayed for "AMP".
    B
    "NCON" is displayed for "RSE" (w/ rear seat entertainment system).
    C
    "OK" is displayed for all items.
    D

    HINT:
    1. When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.
    2. The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.

Text in Illustration 
*1
Node position number for devices that use MOST communication
*2
Device name
*3
Result


B
Go to step 5

C
Go to step 8

D
Go to step 11
A


2. CHECK MOST COMMUNICATION CONNECTOR
  1. Check MOST communication line connector.

    1. Check if a MOST communication line connector between the display and navigation module display and radio receiver assembly has any connection problems (Click here).

  1. Display the "MOST Line Check" screen and check the result (Click here).

    Result 
    Result
    Proceed to
    "NCON" is displayed for "AUDIO".
    A
    The screen cannot be changed to the "MOST Line Check" screen.
    B

    HINT:
    When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.



B
END
A


3. CHECK HARNESS AND CONNECTOR (WAKE UP SIGNAL)

  1. E192430E11
    Disconnect the F56 radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F56-12 (WUI) - Body ground
    Engine switch on (ACC)
    4.5 V or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Radio Receiver Assembly)


NG
Go to step 4
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)

4. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - DISPLAY AND NAVIGATION MODULE DISPLAY)
  1. Disconnect the F56 radio receiver assembly connector.

  1. Disconnect the F65 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F56-12 (WUI) - F65-8 (WUO)
    Always
    Below 1 Ω
    F56-12 (WUI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)

5. CHECK MOST COMMUNICATION CONNECTOR
  1. Check MOST communication line connector.

    1. Check if a MOST communication line connector between the radio receiver assembly and stereo component amplifier assembly has any connection problems (Click here).

  1. Display the "MOST Line Check" screen and check the result (Click here).

    Result 
    Result
    Proceed to
    "NCON" is displayed for "AMP".
    A
    The screen cannot be changed to the "MOST Line Check" screen.
    B

    HINT:
    When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.



B
END
A


6. CHECK HARNESS AND CONNECTOR (WAKE UP SIGNAL)

  1. E192423E02
    Disconnect the F59 stereo component amplifier assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F59-3 (WUI) - Body ground
    Engine switch on (ACC)
    4.5 V or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Stereo Component Amplifier Assembly)


NG
Go to step 7
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

7. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - RADIO RECEIVER)
  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Disconnect the F56 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F59-3 (WUI) - F56-26 (WUO)
    Always
    Below 1 Ω
    F59-3 (WUI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)

8. CHECK MOST COMMUNICATION CONNECTOR
  1. Check MOST communication line connector.

    1. Check if a MOST communication line connector between the stereo component amplifier assembly and television display assembly has any connection problems (Click here).

  1. Display the "MOST Line Check" screen and check the result (Click here).

    Result 
    Result
    Proceed to
    "NCON" is displayed for "RSE".
    A
    The screen cannot be changed to the "MOST Line Check" screen.
    B

    HINT:
    When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.



B
END
A


9. CHECK HARNESS AND CONNECTOR (WAKE UP SIGNAL)

  1. E192430E12
    Disconnect the L39 television display assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    L39-7 (WUI) - Body ground
    Engine switch on (ACC)
    4.5 V or higher

Text in Illustration 
*1
Front view of wire harness connector
(to Television Display Assembly)


NG
Go to step 10
OK

REPLACE TELEVISION DISPLAY ASSEMBLY (Click here)

10. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY - STEREO COMPONENT AMPLIFIER)
  1. Disconnect the L39 television display assembly connector.

  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L39-7 (WUI) - F59-9 (WUO)
    Always
    Below 1 Ω
    L39-7 (WUI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

11. CHECK HARNESS AND CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - RADIO RECEIVER)
  1. Disconnect the F65 display and navigation module display connector.

  1. Disconnect the F56 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F65-3 (MO+) - F56-9 (MI+)
    Always
    Below 1 Ω
    F65-7 (MO-) - F56-23 (MI-)
    Always
    Below 1 Ω
    F65-6 (SLDO) - F56-10 (SLDI)
    Always
    Below 1 Ω
    F65-3 (MO+) - Body ground
    Always
    10 kΩ or higher
    F65-7 (MO-) - Body ground
    Always
    10 kΩ or higher
    F65-6 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - STEREO COMPONENT AMPLIFIER)
  1. Disconnect the F56 radio receiver assembly connector.

  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F56-11 (MO+) - F59-4 (MI+)
    Always
    Below 1 Ω
    F56-25 (MO-) - F59-10 (MI-)
    Always
    Below 1 Ω
    F56-24 (SLDI) - F59-5 (SLDI)
    Always
    Below 1 Ω
    F56-11 (MO+) - Body ground
    Always
    10 kΩ or higher
    F56-25 (MO-) - Body ground
    Always
    10 kΩ or higher
    F56-24 (SLDI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


13. CONFIRM MODEL
  1. Choose the model to be inspected.

    Result 
    Result
    Proceed to
    w/o Rear Seat Entertainment System
    A
    w/ Rear Seat Entertainment System
    B



B
Go to step 16
A


14. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT - DISPLAY AND NAVIGATION MODULE DISPLAY)
  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Disconnect the F65 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F59-6 (MO+) - F65-1 (MI+)
    Always
    Below 1 Ω
    F59-12 (MO-) - F65-5 (MI-)
    Always
    Below 1 Ω
    F59-11 (SLDO) - F65-2 (SLDI)
    Always
    Below 1 Ω
    F59-6 (MO+) - Body ground
    Always
    10 kΩ or higher
    F59-12 (MO-) - Body ground
    Always
    10 kΩ or higher
    F59-11 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)

16. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - TELEVISION DISPLAY)
  1. Disconnect the F59 stereo component amplifier assembly connector.

  1. Disconnect the L39 television display assembly.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F59-6 (MO+) - L39-1 (MI+)
    Always
    Below 1 Ω
    F59-12 (MO-) - L39-2 (MI-)
    Always
    Below 1 Ω
    F59-11 (SLDO) - L39-3 (SLDI)
    Always
    Below 1 Ω
    F59-6 (MO+) - Body ground
    Always
    10 kΩ or higher
    F59-12 (MO-) - Body ground
    Always
    10 kΩ or higher
    F59-11 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


17. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY - DISPLAY AND NAVIGATION MODULE DISPLAY)
  1. Disconnect the L39 television display assembly.

  1. Disconnect the F65 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    L39-6 (MO+) - F65-1 (MI+)
    Always
    Below 1 Ω
    L39-5 (MO-) - F65-5 (MI-)
    Always
    Below 1 Ω
    L39-4 (SLDO) - F65-2 (SLDI)
    Always
    Below 1 Ω
    L39-6 (MO+) - Body ground
    Always
    10 kΩ or higher
    L39-5 (MO-) - Body ground
    Always
    10 kΩ or higher
    L39-4 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


18. CHECK DTC
  1. Clear the DTCs (Click here).

  1. Recheck for DTCs and check if the same trouble occurs again.

    OK:
    No DTCs are output.



NG
REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)
OK

USE SIMULATION METHOD TO CHECK (Click here)


← B15C2 Speed Signal Malfunction (Sep 2011 – Dec 2011)B15D8 Monitor Disconnected (Sep 2011 – Dec 2011) →