2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. REMOVE V-BANK COVER

  1. A267633E01
    Raise the front of the V-bank cover to detach the 2 pins. Then remove the 2 V-bank cover hooks from the bracket, and remove the V-bank cover.
    Text in Illustration 
    *1
    Pin
    *2
    Hook


2. REMOVE AIR CLEANER CAP AND HOSE

  1. Remove the air cleaner cap and hose.

    1. A267624
      Disconnect the mass air flow meter connector, vacuum hose and No. 2 PCV hose and detach the clamp.

    2. Loosen the clamp.

    3. Unfasten the 4 hook clamps, and then remove the bolt and the air cleaner cap and hose.


3. REMOVE AIR CLEANER CASE SUB-ASSEMBLY
  1. Remove the air cleaner filter element.

  1. A270980
    Remove the 3 bolts and air cleaner case.


4. REMOVE FRONT FENDER APRON TRIM PACKING B

  1. A177004
    w/ KDSS:
    Remove the 3 clips and front fender apron trim packing B.

  1. A176301
    w/o KDSS:
    Remove the 4 clips and front fender apron trim packing B.


5. REMOVE FRONT FENDER APRON TRIM PACKING D

  1. A177005
    Remove the 4 clips and front fender apron trim packing D.


6. REMOVE FRONT FENDER APRON TRIM PACKING A

  1. A177003
    Remove the 3 clips and front fender apron trim packing A.


7. REMOVE FRONT FENDER APRON TRIM PACKING C

  1. A177002
    Remove the 4 clips and front fender apron trim packing C.


8. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


9. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


10. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover.


11. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


12. REMOVE FRONT EXHAUST PIPE ASSEMBLY
(Click here)

13. REMOVE MANIFOLD STAY

  1. A272722
    Remove the 3 bolts and manifold stay.


14. REMOVE AIR TUBE (w/ Secondary Air Injection System)

  1. A223569
    Remove the 2 bolts, 2 nuts and air tube.

  1. Remove the 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.


15. DISCONNECT NO. 2 STEERING INTERMEDIATE SHAFT SUB-ASSEMBLY
  1. for Manual Tilt and Manual Telescopic Steering Column: (Click here)
  2. for Power Tilt and Power Telescopic Steering Column: (Click here)

16. REMOVE NO. 1 EXHAUST MANIFOLD HEAT INSULATOR

  1. A272723
    Remove the 3 bolts and heat insulator.


17. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY RH

  1. A271368E01
    Disconnect the air fuel ratio sensor connector.
    Text in Illustration 
    *A
    w/ Secondary Air Injection System
    *B
    w/o Secondary Air Injection System

  1. Remove the 6 nuts, exhaust manifold sub-assembly RH and gasket.


18. REMOVE AIR FUEL RATIO SENSOR (for Bank 1 Sensor 1)

  1. A223682E01
    Using SST, remove the air fuel ratio sensor.
    SST
    09224-00010  


19. REMOVE NO. 2 MANIFOLD STAY

  1. A176353
    Remove the 3 bolts and No. 2 manifold stay.


20. REMOVE NO. 2 AIR TUBE (w/ Secondary Air Injection System)

  1. A223563
    Remove the 2 bolts, 2 nuts and No. 2 air tube.

  1. Remove the 2 gaskets.

    NOTICE:
    Be careful not to damage the installation surface of the gaskets.


21. REMOVE NO. 2 EXHAUST MANIFOLD HEAT INSULATOR

  1. A272724
    Remove the 3 bolts and heat insulator.


22. REMOVE EXHAUST MANIFOLD SUB-ASSEMBLY LH

  1. A271369E01
    Disconnect the air fuel ratio sensor connector.
    Text in Illustration 
    *A
    w/ Secondary Air Injection System
    *B
    w/o Secondary Air Injection System

  1. Remove the 6 nuts, exhaust manifold sub-assembly LH and gasket.


23. REMOVE AIR FUEL RATIO SENSOR (for Bank 2 Sensor 1)

  1. A223684E01
    Using SST, remove the air fuel ratio sensor.
    SST
    09224-00010  

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →