DISASSEMBLY
Removal / installation · Vehicles built from Sep 2011
- CAUTION:
- Wear protective gloves. Sharp areas on the parts may injure your hands.
| 1. REMOVE REAR SEAT HEADREST ASSEMBLY |
- HINT:
- Use the same procedure to remove the rear seat headrest assembly on the other side.
Remove the rear seat headrest assembly.
| 2. REMOVE RECLINING REMOTE CONTROL LEVER KNOB |
- HINT:
- Use the same procedure to remove the reclining remote control lever knob on the other side.
Remove the screw and reclining remote control lever knob.

| 3. REMOVE RECLINING REMOTE CONTROL BEZEL |
- HINT:
- Use the same procedure to remove the reclining remote control bezel on the other side.
Remove the screw.

Detach the hook and remove the reclining remote control bezel.
| 4. REMOVE SEAT ADJUSTER COVER |
- HINT:
- Use the same procedure to remove the seat adjuster cover on the other side.
Using a screwdriver, detach the 2 claws and remove the seat adjuster cover from the No. 1 reclining adjuster release handle LH.

Text in Illustration *1
Protective Tape
- HINT:
- Tape the screwdriver tip before use.
| 5. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH |
Remove the screw and No. 1 reclining adjuster release handle LH.

| 6. REMOVE NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH |
- HINT:
- Use the same procedure described for the LH side.
| 7. REMOVE SEATBACK COVER WITH PAD |
![]() ![]() |
Detach the 2 hooks and open the 2 fasteners.
Text in Illustration *1
Hook
*2
Fastener
Using a clip remover, remove the 2 clips.

Remove the rear seatback cover.

Detach the 4 claws and remove the 2 rear seat headrest supports.

- HINT:
- Use the same procedure to remove the 2 rear seat headrest supports on the other side.
Remove the seatback cover with pad from the rear seatback frame sub-assembly.
| 8. REMOVE BENCH TYPE REAR SEATBACK COVER |
Remove the hog rings and bench type rear seatback cover from the bench type rear seatback pad.

| 9. REMOVE REAR SEAT NO. 1 RECLINING COVER LH |
![]() ![]() |
Remove the screw.
Detach the guide and remove the rear seat No. 1 reclining cover LH.
| 10. REMOVE REAR SEAT NO. 1 RECLINING COVER RH |
- HINT:
- Use the same procedure described for the LH side.
| 11. REMOVE NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY |


| *1 |
Cable End |
- |
- |
Detach the 4 cable clamps from both sides of the rear seat reclining adjuster assembly as shown in the illustration.
Disconnect the 4 cable ends from both sides of the rear seat reclining adjuster assembly as shown in the illustration.
Detach the 8 cable clamps and remove the No. 2 seat adjuster control cable assembly.
| 12. REMOVE REAR SEATBACK FRAME SUB-ASSEMBLY |
![]() ![]() |
Remove the 4 bolts and rear seatback frame sub-assembly.
| 13. REMOVE REAR SEAT CUSHION |
![]() ![]() |
Remove the screw and rear seat cushion.
| 14. REMOVE FOLD SEAT STOPPER BAND ASSEMBLY |
![]() ![]() |
Remove the screw and rear seat cushion together with the fold seat stopper band assembly.
| 15. REMOVE REAR SEAT TURN LOCK COVER |
![]() ![]() |
Remove the 2 screws and rear seat turn lock cover.
| 16. REMOVE SEAT CUSHION COVER WITH PAD |
![]() ![]() |
Open the 2 fasteners and detach the fastening tape.
Text in Illustration *1
Fastener
*2
Fastening Tape
Detach the 2 hooks.

Text in Illustration *1
Hook
Remove the hog rings and seat cushion cover with pad from the rear seat cushion frame sub-assembly.
| 17. REMOVE BENCH TYPE REAR SEAT CUSHION COVER |
![]() ![]() |
Remove the hog rings.
Remove the hog rings and bench type rear seat cushion cover from the rear No. 1 seat cushion pad.

| 18. REMOVE REAR SEATBACK LOCK COVER |
- HINT:
- Use the same procedure to remove the rear seatback lock cover on the other side.
Remove the 2 screws and rear seatback lock cover from the rear seat lock assembly LH.

| 19. REMOVE REAR SEAT RECLINING ADJUSTER ASSEMBLY LH |
Remove the 2 bolts and rear seat reclining adjuster assembly LH from the rear seat cushion frame sub-assembly.

| 20. REMOVE REAR SEAT RECLINING ADJUSTER ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
| 21. REMOVE REAR SEAT HINGE COVER |
- HINT:
- Use the same procedure to remove the rear seat hinge cover on the other side.
Remove the rear seat hinge cover from the rear seat reclining adjuster assembly LH.

| 22. REMOVE REAR SEAT LOCK CONTROL CABLE |


| *1 |
Tension Spring |
*2 |
Cable End A |
| *3 |
Cable End B |
- |
- |
Remove the 2 tension springs from both sides of the rear seat cushion frame sub-assembly as shown in the illustration.
Detach the 2 cable clamps.
Twist the 2 cable ends A and disconnect them from both sides of the rear seat cushion frame sub-assembly as shown in the illustration.
Detach the 2 cable clamps.
Twist the 2 cable ends B and disconnect them from both sides of the rear seat lock assembly as shown in the illustration.
Pull out the 2 cable ends B from the 2 holes of the rear seat cushion frame sub-assembly as shown in the illustration.
Detach the 2 cable clamps and remove the rear seat lock control cable from the rear seat cushion frame sub-assembly.
| 23. REMOVE REAR SEAT INNER BELT ASSEMBLY |
![]() ![]() |
Open the 2 fasteners and detach the fastening tape.
Text in Illustration *1
Fastener
*2
Fastening Tape
Remove the bolt and rear seat inner belt assembly.

| 24. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY LH |
Remove the rear No. 1 seat inner belt assembly LH.

| 25. REMOVE REAR SEAT LOCK ASSEMBLY LH |
![]() ![]() |
Remove the rear seat No. 1 cushion spring.
Remove the rear seat lock assembly LH from the rear seat cushion frame sub-assembly.

| 26. REMOVE FOLD SEAT LOCK COLLAR |
- HINT:
- Use the same procedure to remove the fold seat lock collar on the other side.
Remove the fold seat lock collar from the rear seat lock assembly LH.

| 27. REMOVE REAR SEAT OUTER BELT ASSEMBLY |
Remove the bolt and rear seat outer belt assembly.

| 28. REMOVE REAR NO. 1 SEAT INNER BELT ASSEMBLY RH |
Remove the rear No. 1 seat inner belt assembly RH.

| 29. REMOVE REAR SEAT LOCK ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
| 30. REMOVE REAR SEAT HINGE SUB-ASSEMBLY LH |
![]() ![]() |
Remove the 2 E-rings.
Remove the 2 rear seat hinge pins and rear seat hinge sub-assembly LH from the rear seat cushion frame sub-assembly.
| 31. REMOVE REAR SEAT HINGE SUB-ASSEMBLY RH |
- HINT:
- Use the same procedure described for the LH side.
| 32. REMOVE REAR SEAT CUSHION SUPPORT SPRING |
- HINT:
- Use the same procedure to remove the rear seat cushion support spring on the other side.
Remove the 2 rear seat hinge set plates and rear seat cushion support spring from the rear seat cushion frame sub-assembly.

| 33. REMOVE REAR SEAT CUSHION SPACER |
- HINT:
- Use the same procedure to remove the rear seat cushion spacer on the other side.
Remove the rear seat cushion spacer from the rear seat cushion support spring.











