2011-2013 Land Cruiser · Service Manual Vehicle Interior

REASSEMBLY

Removal / installation · Vehicles built from Sep 2011

CAUTION:
Wear protective gloves. Sharp areas on the parts may injure your hands.


1. INSTALL REAR SEAT CUSHION SPACER

HINT:
Use the same procedure to install the rear seat cushion spacer on the other side.

  1. B292844
    Install the rear seat cushion spacer to the rear seat cushion support spring.


2. INSTALL REAR SEAT CUSHION SUPPORT SPRING

HINT:
Use the same procedure to install the rear seat cushion support spring on the other side.

  1. Install the rear seat cushion support spring to the rear seat cushion frame sub-assembly with the 2 rear seat hinge set plates.


3. INSTALL REAR SEAT HINGE SUB-ASSEMBLY LH
  1. Install the rear seat hinge sub-assembly LH to the rear seat cushion frame sub-assembly with the 2 rear seat hinge pins.

  1. Install 2 new E-rings.


4. INSTALL REAR SEAT HINGE SUB-ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


5. INSTALL FOLD SEAT LOCK COLLAR

HINT:
Use the same procedure to install the fold seat lock collar on the other side.

  1. Install the fold seat lock collar to the rear seat lock assembly LH.


6. INSTALL REAR SEAT LOCK ASSEMBLY LH

B292849
  1. Install the rear seat lock assembly LH to the rear seat cushion frame sub-assembly.

  1. Install the rear seat No. 1 cushion spring.


7. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY LH

  1. B293896E01
    Temporarily install the rear No. 1 seat inner belt assembly LH.

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat inner belt assembly LH to overlap the protruding parts of the rear seat.

    Text in Illustration 
    *1
    Protruding Part


8. INSTALL REAR SEAT INNER BELT ASSEMBLY

  1. B293895E01
    Install the rear seat inner belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear seat inner belt assembly to overlap the protruding parts of the rear No. 1 seat inner belt assembly LH.

    Text in Illustration 
    *1
    Protruding Part

  1. B292832E01
    Close the 2 fasteners and attach the fastening tape.
    Text in Illustration 
    *1
    Fastener
    *2
    Fastening Tape


9. INSTALL REAR SEAT LOCK ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


10. INSTALL REAR NO. 1 SEAT INNER BELT ASSEMBLY RH

  1. B293897E01
    Temporarily install the rear No. 1 seat inner belt assembly RH.

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat inner belt assembly RH to overlap the protruding parts of the rear seat.

    Text in Illustration 
    *1
    Protruding Part


11. INSTALL REAR SEAT OUTER BELT ASSEMBLY

  1. B293894E01
    Install the rear seat outer belt assembly with the bolt.

    Torque:
    42 N*m{ 428 kgf*cm , 31 ft.*lbf }

    NOTICE:
    Do not allow the anchor part of the rear No. 1 seat outer belt assembly to overlap the protruding parts of the rear seat inner belt assembly RH.

    Text in Illustration 
    *1
    Protruding Part


12. INSTALL REAR SEAT LOCK CONTROL CABLE

B292840E01
Text in Illustration 
*1
Cable End A
*2
Tension Spring
*3
Cable End B
-
-
  1. Attach the 2 cable clamps to install the rear seat lock control cable to the rear seat cushion frame sub-assembly.

  1. Pass the 2 cable ends B through the 2 holes of the rear seat cushion frame sub-assembly as shown in the illustration.

  1. Insert and twist the 2 cable ends B to connect them to both sides of the rear seat lock assembly as shown in the illustration.

  1. Attach the 2 cable clamps.

  1. Insert and twist the 2 cable ends A to connect them to both sides of the rear seat cushion frame sub-assembly as shown in the illustration.

  1. Attach the 2 cable clamps.

  1. Install the 2 tension springs to both sides of the rear seat cushion frame sub-assembly as shown in the illustration.


13. INSTALL REAR SEAT HINGE COVER

HINT:
Use the same procedure to install the rear seat hinge cover on the other side.

  1. B292838
    Install the rear seat hinge cover to the rear seat reclining adjuster assembly LH.


14. INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY LH
  1. Install the rear seat reclining adjuster assembly LH to the rear seat cushion frame sub-assembly with the 2 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


15. INSTALL REAR SEAT RECLINING ADJUSTER ASSEMBLY RH

HINT:
Use the same procedure described for the LH side.


16. INSTALL REAR SEATBACK LOCK COVER

HINT:
Use the same procedure to install the rear seatback lock cover on the other side.

  1. Install the rear seatback lock cover to the rear seat lock assembly LH with the 2 screws.


17. INSTALL BENCH TYPE REAR SEAT CUSHION COVER

B293928E01
  1. Temporarily install the bench type rear seat cushion cover to the rear No. 1 seat cushion pad.

  1. Using hog ring pliers, install new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. B293926E01
    Using hog ring pliers, install new hog rings.
    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


18. INSTALL SEAT CUSHION COVER WITH PAD

B292834E01
  1. Set the seat cushion cover with pad in place.

  1. Using hog ring pliers, install the seat cushion cover with pad to the rear seat cushion frame sub-assembly with new hog rings.

    Text in Illustration 
    *1
    Hook
    *2
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.

  1. Attach the 2 hooks.

  1. B292832E01
    Attach the fastening tape and close the 2 fasteners.
    Text in Illustration 
    *1
    Fastener
    *2
    Fastening Tape


19. INSTALL REAR SEAT TURN LOCK COVER
  1. Install the rear seat turn lock cover with the 2 screws.


20. INSTALL FOLD SEAT STOPPER BAND ASSEMBLY
  1. Install the fold seat stopper band assembly together with the rear seat cushion with the screw.


21. INSTALL REAR SEAT CUSHION
  1. Install the rear seat cushion with the screw.


22. INSTALL REAR SEATBACK FRAME SUB-ASSEMBLY
  1. Install the rear seatback frame sub-assembly with the 4 bolts.

    Torque:
    37 N*m{ 377 kgf*cm , 27 ft.*lbf }


23. INSTALL NO. 2 SEAT ADJUSTER CONTROL CABLE ASSEMBLY

B292826E01
Text in Illustration 
*1
Cable End
-
-
  1. Attach the 8 cable clamps to install the No. 2 seat adjuster control cable assembly.

  1. Connect the 4 cable ends to both sides of the rear seat reclining adjuster assembly as shown in the illustration.

  1. Attach the 4 cable clamps to both sides of the rear seat reclining adjuster assembly as shown in the illustration.


24. INSTALL REAR SEAT NO. 1 RECLINING COVER LH
  1. Attach the guide to install the rear seat No. 1 reclining cover LH.

  1. Install the screw.


25. INSTALL REAR SEAT NO. 1 RECLINING COVER RH

HINT:
Use the same procedure described for the LH side.


26. INSTALL BENCH TYPE REAR SEATBACK COVER

B292823E01
  1. Temporarily install the bench type rear seatback cover to the bench type rear seatback pad.

  1. Using hog ring pliers, install new hog rings.

    Text in Illustration 
    *1
    Hog Ring Pliers

    NOTICE:
    1. Be careful not to damage the cover.
    2. When installing the hog rings, avoid wrinkling the cover.


27. INSTALL SEATBACK COVER WITH PAD
  1. Set the seatback cover with pad in place.

  1. B292820
    Install the seatback cover.

  1. Install the 2 clips.

  1. Attach the 4 claws to install the 2 rear seat headrest supports.

    HINT:
    Use the same procedure to install the 2 rear seat headrest supports on the other side.

  1. B292817E01
    Close the 2 fasteners and attach the 2 hooks.
    Text in Illustration 
    *1
    Hook
    *2
    Fastener


28. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE LH

  1. B292815
    Install the No. 1 reclining adjuster release handle LH with the screw.


29. INSTALL NO. 1 RECLINING ADJUSTER RELEASE HANDLE RH

HINT:
Use the same procedure described for the LH side.


30. INSTALL SEAT ADJUSTER COVER

HINT:
Use the same procedure to install the seat adjuster cover on the other side.

  1. B292813
    Attach the 2 claws to install the seat adjuster cover to the No. 1 reclining adjuster release handle LH.


31. INSTALL RECLINING REMOTE CONTROL BEZEL

HINT:
Use the same procedure to install the reclining remote control bezel on the other side.

  1. B292811
    Attach the hook to install the reclining remote control bezel.

  1. Install the screw.


32. INSTALL RECLINING REMOTE CONTROL LEVER KNOB

HINT:
Use the same procedure to install the reclining remote control lever knob on the other side.

  1. B292809
    Install the reclining remote control lever knob with the screw.


33. INSTALL REAR SEAT HEADREST ASSEMBLY

HINT:
Use the same procedure to install the rear seat headrest assembly on the other side.

  1. Install the rear seat headrest assembly.

← DISASSEMBLY (from Sep 2011)INSTALLATION (from Sep 2011) →