2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B1579 Voice Recognition Microphone Disconnected

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

The multi-media module receiver assembly and map light assembly (telephone microphone assembly) are connected to each other using the microphone connection detection signal lines.
This DTC is stored when a microphone connection detection signal line is disconnected.
DTC Code
DTC Detection Condition
Trouble Area
B1579
Telephone microphone signal is lost.
  1. Multi-media module receiver assembly
  2. Map light assembly
  3. Telephone microphone assembly
  4. Harness or connector

WIRING DIAGRAM

E248564E01

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - MAP LIGHT ASSEMBLY)
  1. Disconnect the F77 multi-media module receiver assembly connector.

  1. Disconnect the R7 map light assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-49 (SNS2) - R7-20 (SNS2)
    Always
    Below 1 Ω
    F77-29 (MACC) - R7-25 (ACC)
    Always
    Below 1 Ω
    F77-27 (MIN+) - R7-27 (MI1+)
    Always
    Below 1 Ω
    F77-48 (MIN-) - R7-26 (MIC-)
    Always
    Below 1 Ω
    F77-49 (SNS2) - Body ground
    Always
    10 kΩ or higher
    F77-29 (MACC) - Body ground
    Always
    10 kΩ or higher
    F77-27 (MIN+) - Body ground
    Always
    10 kΩ or higher
    F77-48 (MIN-) - Body ground
    Always
    10 kΩ or higher
    F77-28 (SGND) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


2. CHECK MULTI-MEDIA MODULE RECEIVER ASSEMBLY

  1. E239014E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F77-28 (SGND) - Body ground
    Always
    Below 1 Ω
    F77-48 (MIN-) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F77-29 (MACC) - Body ground
    Engine switch on (ACC)
    4 to 6 V

Text in Illustration 
*a
Component with harness connected
(Multi-media Module Receiver Assembly)


NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK


3. INSPECT MAP LIGHT ASSEMBLY

  1. E248565E01
    Remove the map light assembly (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    26 (MIC-) - 20 (SNS2)
    Always
    Below 1 Ω



NG
Go to step 5
OK


4. CHECK MAP LIGHT ASSEMBLY
E248566E01
  1. Turn the engine switch on (ACC).

  1. Connect an oscilloscope to terminals R7-27 (MI1+) and R7-26 (MIC-) of the map light assembly connector.

  1. Check the waveform of the telephone microphone assembly using the oscilloscope.

    Text in Illustration 
    *a
    Component with harness connected
    (Map Light Assembly)
    Result 
    Result
    Proceed to
    A waveform synchronized with the voice input to the map light assembly is not output.
    A
    A waveform synchronized with the voice input to the map light assembly is output.
    B



B
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
A


5. CHECK TELEPHONE MICROPHONE ASSEMBLY
  1. Replace the telephone microphone assembly with a new or normally functioning one (Click here).

  1. Check if the same DTC is output again.

    Result 
    Result
    Proceed to
    No DTCs are output.
    A
    DTCs are output.
    B



B
REPLACE MAP LIGHT ASSEMBLY (Click here)
A

END (TELEPHONE MICROPHONE ASSEMBLY IS DEFECTIVE)


← B1575 GVIF Disconnected (from EMV/MM Integrated Device to Multi Display) (from Jan 2012)B15A0 LAN Master Malfunction (+ B15AD) (from Jan 2012) →