Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM J

1UR-FE ENGINE CONTROL  SFI SYSTEM  MIL Circuit  


DESCRIPTION

The MIL (Malfunction Indicator Lamp) is used to indicate the detection of vehicle malfunctions by the ECM. When the engine switch is turned on (IG), power is supplied to the MIL circuit and the ECM provides the circuit ground which illuminates the MIL.

The MIL operation can be checked visually. When the engine switch is first turned on (IG), the MIL should be illuminated and should then turn off when the engine is started. If the MIL remains illuminated or is not illuminated, conduct the following troubleshooting procedure using the GTS.

WIRING DIAGRAM

A182518E14
5.938,2.448 6.896,2.615 0.958,0.167 10 false A52*1, A38*2 6.198,2.656 6.594,2.813 0.396,0.156 10 false ECM 6.031,1 6.25,1.156 0.219,0.156 10 false W 5.698,1.25 5.896,1.406 0.198,0.156 10 false 24 4.906,1.115 5.229,1.271 0.323,0.156 10 false E8 4.948,0.927 5.146,1.083 0.198,0.156 10 false 12 2.74,1.104 3.063,1.26 0.323,0.156 10 false E7 2.771,0.906 2.969,1.063 0.198,0.156 10 false 18 3.708,1.281 4,1.448 0.292,0.167 10 false MIL 4.51,1.229 4.844,1.396 0.333,0.167 10 false CHK 3.063,1.229 3.344,1.438 0.281,0.208 10 false IG+ 2,0.938 2.354,1.104 0.354,0.167 10 false MET 3.375,2.083 4.813,2.302 1.438,0.219 10 false Combination Meter 0.479,1.115 1.5,1.323 1.021,0.208 10 false from IG2 relay 0.698,2.802 1.771,3 1.073,0.198 10 false *1: for LHD 0.698,3.292 1.771,3.49 1.073,0.198 10 false *2: for RHD 2.26,1.281 2.469,1.438 0.208,0.156 10 false 2 1.958,1.281 2.167,1.438 0.208,0.156 10 false 1

PROCEDURE

1.CHECK THAT MIL IS ILLUMINATED
a.

Perform troubleshooting in accordance with the table below.

Result
Result Proceed to
MIL remains on A
MIL does not illuminate B



A

2.CHECK WHETHER MIL TURNS OFF

B

5.CHECK THAT MIL IS ILLUMINATED
2.CHECK WHETHER MIL TURNS OFF
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes.


e.

Check if any DTCs have been stored. Note down any DTCs.



g.

Check if the MIL goes off.

OK:

MIL goes off.




OK

NG

3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
3.CHECK HARNESS AND CONNECTOR (CHECK FOR SHORT IN WIRE HARNESS)
a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Check that the MIL is not illuminated.

OK:

MIL is not illuminated.




OK

NG

4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
4.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
A52-24 (W) or E8-12 (CHK) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
A38-24 (W) or E8-12 (CHK) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK THAT MIL IS ILLUMINATED
a.

Check if the MIL is illuminated when the engine switch is turned on (IG).

OK:

MIL is illuminated.




OK

END

NG

6.CHECK THAT ENGINE STARTS
6.CHECK THAT ENGINE STARTS
a.

Turn the engine switch on (IG).


b.

Start the engine.

Result
Result Proceed to
Engine starts A
Engine does not start* B

HINT:

*: The GTS cannot communicate with the ECM.




A

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)

B

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
A52-24 (W) - E8-12 (CHK) Always Below 1 Ω

for LHD
Tester Connection Condition Specified Condition
A38-24 (W) - E8-12 (CHK) Always Below 1 Ω




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR