Home › Vehicle Interior › METER / GAUGE / DISPLAY › COMBINATION METER(w/ Multi-information Display) › 2014.08–2015.08
RM2660E _58 Vehicle Interior _052841 METER / GAUGE / DISPLAY _0255595 COMBINATION METER(w/ Multi-information Display) A

METER / GAUGE / DISPLAY  COMBINATION METER(w/ Multi-information Display)  REMOVAL  


PROCEDURE

Hide 1. DISABLE AUTO TILT AWAY FUNCTION

a.

Disable the function by changing the customize parameter (See page General>INTRODUCTION>REPAIR INSTRUCTION>CUSTOMIZE PARAMETERS).

NOTICE:

Record the current customize parameter setting (whether the Autoaway/Return function is enabled or disabled) in order to restore the current setting after finishing the operation.


HINT:

Performing the above operation causes the Autoaway/Return function to be disabled when the engine switch is turned off.



b.

Turn the engine switch on (IG). Operate the tilt and telescopic switch to fully extend and lower the steering column assembly.


c.

Turn the engine switch off.


Hide 2. PRECAUTION

NOTICE:

After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (See page General>INTRODUCTION>REPAIR INSTRUCTION>PRECAUTION).


Hide 3.DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

CAUTION:

Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.


NOTICE:

When disconnecting the cable, some systems need to be initialized after the cable is reconnected (See page General>INTRODUCTION>REPAIR INSTRUCTION>INITIALIZATION).


Hide 55474C 4.REMOVE NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
E154744E01
0.163,1.723 1.171,1.906 1.008,0.184 10 Protective Tape 1.385,1.82 1.494,1.82 false 1.494,1.828 1.494,1.305 false

Place protective tape as shown in the illustration.


b.

Using a moulding remover, detach the 3 claws and remove the panel garnish.


Hide 55449C 5.REMOVE NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION

a.
E155426E01
0.257,1.728 1.255,1.903 0.998,0.174 10 Protective Tape 1.483,1.82 2.027,1.614 false

Place protective tape as shown in the illustration.


b.

Using a moulding remover, detach the 7 claws and remove the panel cushion.


Hide 55403C 6.REMOVE LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY LH

a.
E154742

Remove the clip.


b.

Remove the screw.


c.

Detach the 8 claws.


d.

Remove the panel pad and disconnect the connectors and 2 clamps.


Hide 55475A 7.REMOVE NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

a.
E154741E01
2.18,1.631 3.197,1.796 1.017,0.165 10 Protective Tape 2.142,1.708 1.94,1.708 false 1.944,1.714 1.944,1.469 false

Place protective tape as shown in the illustration.


b.

Using a moulding remover, detach the 2 claws and remove the panel garnish.


Hide 55404C 8.REMOVE INSTRUMENT CLUSTER FINISH PANEL SUB-ASSEMBLY

a.
E155398

Detach the 4 claws.


b.
E154732

Detach the 9 claws.


c.
E155437

Remove the finish panel and disconnect the connector.


Hide 83100 9.REMOVE COMBINATION METER ASSEMBLY

a.
E154733

Remove the 4 screws.


b.
E154734

Disconnect the connectors, and remove the combination meter by pulling it up in the direction of the arrow in the illustration.