Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0102  Mass or Volume Air Flow Circuit Low Input  P0103  Mass or Volume Air Flow Circuit High Input  


DESCRIPTION

The mass air flow meter is a sensor that measures the amount of air flowing through the throttle valve.

The ECM uses this information to determine the fuel injection time and to provide the appropriate air-fuel ratio.

Inside the mass air flow meter, there is a heated platinum wire which is exposed to the flow of intake air.

By applying a specific electrical current to the wire, the ECM heats it to a given temperature. The flow of incoming air cools both the wire and an internal thermistor, affecting their resistance. To maintain a constant current value, the ECM varies the voltage applied to the wire and internal thermistor. The voltage level is proportional to the airflow through the sensor, and the ECM uses it to calculate the intake air volume.

The circuit is constructed so that the platinum hot wire and temperature sensor create a bridge circuit, and the power transistor is controlled so that the potentials of A and B remain equal to maintain the predetermined temperature.

HINT:

When either of these DTCs is stored, the ECM enters fail-safe mode. During fail-safe mode, the ignition timing is calculated by the ECM according to the engine speed and throttle valve position. The ECM continues operating in fail-safe mode until a pass condition is detected.


A160257E01
2.954,2.753 5.064,2.960 2.110,0.207 10 Temperature Sensor (Thermistor) 1.929,0.681 2.184,0.845 0.255,0.163 10 +B 1.878,1.033 2.969,1.179 1.091,0.145 10 Power Transistor 2.18,1.424 3.342,1.595 1.162,0.171 10 Hot Wire (Heater) 5.974,2.76 7.117,2.932 1.143,0.171 10 Hot Wire (Heater) 1.357,2.631 1.593,1.889 false 2.142,1.492 1.962,1.924 false 2.574,2.013 3.560,2.207 0.986,0.194 10 Output Voltage 4.646,2.733 5.424,1.969 false 6.322,2.003 6.116,2.746 false 1.323,1.911 1.487,2.075 0.164,0.165 10 A 2.133,1.904 2.299,2.072 0.165,0.168 10 B 4.967,3.273 6.151,3.439 1.184,0.165 10 Cold Film Element 0.474,2.638 1.658,2.803 1.184,0.165 10 Cold Film Element 5.507,3.235 5.794,1.968 false

DTC No. DTC Detection Condition Trouble Area
P0102 Mass air flow meter voltage is below 0.2 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter assembly

·

ECM


P0103 Mass air flow meter voltage is higher than 4.9 V for 3 seconds (1 trip detection logic).
·

Open or short in mass air flow meter circuit

·

Mass air flow meter assembly

·

ECM



HINT:

When either of these DTCs is stored, check the air flow rate by entering the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.

MAF (gm/s) Malfunction
Approximately 0.0
·

Open in mass air flow meter power source circuit

·

Open or short in VG circuit


160.0 or more Open in E2G circuit


MONITOR DESCRIPTION

If there is a defect in the mass air flow meter or an open or short circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the mass air flow meter and stores a DTC.

Example:

When the sensor output voltage remains at below 0.2 V, or higher than 4.9 V for more than 3 seconds, the ECM stores a DTC.

If the malfunction is not repaired successfully, a DTC is stored 3 seconds after the engine is next started.

CONFIRMATION DRIVING PATTERN

1.

Turn the engine switch on (IG) and wait for 5 seconds or more.


WIRING DIAGRAM

U163728E01
0.508,2.684 1.007,2.867 0.498,0.184 10 Battery 0.929,0.75 1.575,0.915 0.647,0.165 10 EFI MAIN 0.592,0.595 0.804,0.750 0.211,0.156 10 1C 0.639,0.407 0.758,0.591 0.119,0.184 10 1 2.451,0.588 2.663,0.744 0.211,0.156 10 1B 2.498,0.401 2.617,0.585 0.119,0.184 10 4 2.439,0.973 2.651,1.129 0.211,0.156 10 1B 2.486,0.786 2.605,0.969 0.119,0.184 10 2 1.219,1.39 1.431,1.546 0.211,0.156 10 1B 1.008,1.384 1.127,1.568 0.119,0.184 10 3 1.751,1.329 2.008,1.504 0.258,0.174 10 EFI 1.475,1.61 2.960,1.803 1.485,0.193 10 No. 1 Integration Relay 2.759,0.732 3.397,0.906 0.637,0.174 10 EFI NO. 2 3.315,0.493 3.453,0.668 0.137,0.174 10 1 4.8,0.83 4.938,1.004 0.137,0.174 10 3 4.8,1.371 4.938,1.546 0.137,0.174 10 2 3.488,0.479 3.709,0.645 0.221,0.165 10 +B 4.506,0.844 4.745,1.009 0.239,0.165 10 VG 5.814,0.844 6.053,1.009 0.239,0.165 10 VG 4.422,1.376 4.745,1.541 0.323,0.165 10 E2G 5.814,1.376 6.136,1.541 0.323,0.165 10 E2G 3.256,1.918 3.550,2.083 0.295,0.165 10 C50 3.242,2.077 5.212,2.242 1.971,0.165 10 Mass Air Flow Meter Assembly 6.271,3.254 6.603,3.419 0.332,0.165 10 ECM 5.44,0.76 5.755,0.925 0.314,0.165 10 74*2 5.44,1.311 5.784,1.476 0.343,0.165 10 75*2 5.455,0.939 5.740,1.104 0.286,0.165 10 C45 5.469,1.49 5.754,1.655 0.286,0.165 10 C45 5.47,2.867 5.778,3.042 0.309,0.174 10 A38 5.447,2.698 5.751,2.872 0.304,0.174 10 34*2 5.804,2.768 6.247,2.933 0.443,0.165 10 MREL 5.083,0.76 5.397,0.925 0.314,0.165 10 74*1 5.083,1.311 5.426,1.476 0.343,0.165 10 75*1 5.098,0.939 5.383,1.104 0.286,0.165 10 C46 5.112,1.49 5.397,1.655 0.286,0.165 10 C46 5.112,2.867 5.421,3.042 0.309,0.174 10 A52 5.09,2.698 5.394,2.872 0.304,0.174 10 34*1 1.821,2.773 2.595,2.928 0.774,0.156 10 *1: for RHD 1.821,3.039 2.595,3.195 0.774,0.156 10 *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.READ DTC OUTPUT
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / MAF.


e.

Read the values displayed on the GTS.

Result
Result Proceed to
DTC P0102 is output A
DTC P0103 is output B

HINT:

*: The value must change when the throttle valve is opened or closed with the engine running.




A

2.INSPECT MASS AIR FLOW METER ASSEMBLY (POWER SOURCE VOLTAGE)

B

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
2.INSPECT MASS AIR FLOW METER ASSEMBLY (POWER SOURCE VOLTAGE)
U162870E01
0.275,1.3 0.578,1.468 0.303,0.168 10 C50 0.06,0.002 0.223,0.165 0.163,0.163 10 *a 2.598,0.783 3.032,0.973 0.434,0.191 10 +B (+) 1.406,1.372 2.556,0.883 false

a.

Disconnect the mass air flow meter connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C50-1 (+B) - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Mass Air Flow Meter Assembly)



OK

3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)

NG

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
3.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C46-74 (VG) Always Below 1 Ω
C50-2 (E2G) - C46-75 (E2G) Always Below 1 Ω
C50-3 (VG) or C46-74 (VG) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C45-74 (VG) Always Below 1 Ω
C50-2 (E2G) - C45-75 (E2G) Always Below 1 Ω
C50-3 (VG) or C45-74 (VG) - Body ground Always 10 kΩ or higher




OK

4.INSPECT MASS AIR FLOW METER ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.INSPECT MASS AIR FLOW METER ASSEMBLY
a.

Inspect the mass air flow meter, referring to the On-vehicle Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>ON-VEHICLE INSPECTION).


b.

Inspect the mass air flow meter, referring to the Inspection for Mass Air Flow Meter (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>MASS AIR FLOW METER>INSPECTION).


c.

Inspect the function of the mass air flow meter.

i.

Connect the GTS to the DLC3.


ii.

Turn the engine switch on (IG).


iii.

Turn the GTS on.


iv.

Enter the following menus: Powertrain / Engine and ECT / Data List / MAF.


v.

Start the engine.


vi.

Check that the MAF value changes when the engine is raced.

OK:

The reading changes.





OK

NG

5.CHECK HARNESS AND CONNECTOR (SENSOR GROUND)
a.

Disconnect the mass air flow meter connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-2 (E2G) - Body ground Always Below 1 Ω




OK

NG

6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
6.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - ECM)
a.

Disconnect the mass air flow meter connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C46-74 (VG) Always Below 1 Ω
C50-2 (E2G) - C46-75 (E2G) Always Below 1 Ω
C50-3 (VG) or C46-74 (VG) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C50-3 (VG) - C45-74 (VG) Always Below 1 Ω
C50-2 (E2G) - C45-75 (E2G) Always Below 1 Ω
C50-3 (VG) or C45-74 (VG) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (MASS AIR FLOW METER - NO. 1 INTEGRATION RELAY)
a.

Disconnect the mass air flow meter connector.


b.

Remove the No. 1 integration relay from the engine room relay block.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C50-1 (+B) - 1B-4 Always Below 1 Ω
C50-1 (+B) or 1B-4 - Body ground Always 10 kΩ or higher




OK

REPLACE NO.1 INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR