Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0500  Vehicle Speed Sensor "A"  


DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of this pulse signal.

A115899E11
0.43,1.047 1.579,1.425 1.149,0.378 10 from Wheel Speed Sensor 1.817,1.96 3.237,2.123 1.420,0.163 10 Skid Control ECU 3.722,1.96 5.142,2.123 1.420,0.163 10 Combination Meter 3.113,0.599 3.533,0.776 0.420,0.177 10 Pulse 5.039,0.599 5.441,0.776 0.402,0.177 10 Pulse 6.045,1.324 6.492,1.486 0.448,0.163 10 ECM

DTC No. DTC Detection Condition Trouble Area
P0500 While the vehicle is being driven, no vehicle speed signal is transmitted to the ECM (2 trip detection logic).
·

Open or short in speed signal circuit

·

Wheel speed sensor

·

Combination meter assembly

·

ECM

·

Skid control ECU



MONITOR DESCRIPTION

The ECM assumes that the vehicle is being driven when the vehicle speed measured by the output speed sensor (SP2) is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite this condition being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.


CONFIRMATION DRIVING PATTERN

A232052E01
0.657,0.826 1.855,1.052 1.198,0.225 10 24 km/h (15 mph) 1.421,1.996 1.820,2.166 0.399,0.170 10 Idling 0.907,2.346 1.938,2.727 1.031,0.380 10 Engine Switch on (IG) 2.387,2.221 2.620,2.390 0.232,0.169 10 [A] 4.706,0.42 4.911,0.590 0.205,0.170 10 [B] 6.249,3.234 6.447,3.432 0.198,0.198 10 [C] 3.972,3.019 5.889,3.164 1.916,0.145 10 Total of 30 seconds or more

1.

Connect the GTS to the DLC3.

2.

Turn the engine switch on (IG) and turn the GTS on.

3.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation).

4.

Turn the engine switch off and wait for at least 30 seconds.

5.

Turn the engine switch on (IG) and turn the GTS on [A].

6.

Start the engine.

7.

Drive the vehicle at 24 km/h (15 mph) or more for a total of 30 seconds or more [B].

CAUTION:

When performing the confirmation driving pattern, obey all speed limits and traffic laws.


8.

Stop the vehicle.

9.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes [C].

10.

Read the pending DTCs.

HINT:
·

If a pending DTC is output, the system is malfunctioning.

·

If a pending DTC is not output, perform the following procedure.



11.

Enter the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

12.

Input the DTC: P0500.

13.

Check the DTC judgment result.

Tester Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.




WIRING DIAGRAM

A280190E01
0.229,2.515 0.533,2.690 0.304,0.174 10 A24 1.341,1.717 1.552,1.891 0.211,0.174 10 12 0.99,1.829 1.294,2.003 0.304,0.174 10 SP1 2.657,1.731 2.823,1.905 0.165,0.174 10 SI 3.895,1.637 4.144,1.812 0.248,0.174 10 +S 4.171,1.637 4.313,1.812 0.142,0.174 10 4 2.471,1.731 2.594,1.905 0.123,0.174 10 3 5.329,1.623 5.540,1.798 0.211,0.174 10 13 5.572,1.623 5.876,1.798 0.304,0.174 10 SPD 0.229,2.674 1.394,2.839 1.165,0.165 10 Skid Control ECU 2.48,2.768 4.358,2.979 1.878,0.211 10 Combination Meter Assembly 2.48,2.613 2.710,2.788 0.230,0.174 10 E7 5.73,2.698 6.067,2.866 0.336,0.169 10 ECM 5.73,2.529 6.618,2.695 0.887,0.165 10 A52*1, A38*2 2.34,3.155 3.098,3.316 0.758,0.161 10 *1: for RHD 2.34,3.454 3.098,3.615 0.758,0.161 10 *2: for LHD 5.385,3.062 6.402,3.255 1.017,0.193 10 to Other ECUs

CAUTION / NOTICE / HINT

HINT:

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.CHECK OPERATION OF SPEEDOMETER
a.

Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

HINT:
·

The vehicle speed sensor is operating normally if the speedometer reading is normal.

·

If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (See page Vehicle Interior>METER / GAUGE / DISPLAY>METER / GAUGE SYSTEM>Speedometer Malfunction).





OK

2.READ VALUE USING GTS (VEHICLE SPEED)

NG

2.READ VALUE USING GTS (VEHICLE SPEED)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.


e.

Drive the vehicle.


f.

Read the value displayed on the GTS.

OK:

Vehicle speeds displayed on GTS and speedometer display are equal.




OK

NG

3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
3.CHECK HARNESS AND CONNECTOR (COMBINATION METER - ECM)
a.

Disconnect the ECM connector.


b.

Disconnect the combination meter connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
E7-4 (+S) - A52-13 (SPD) Always Below 1 Ω
E7-4 (+S) or A52-13 (SPD) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
E7-4 (+S) - A38-13 (SPD) Always Below 1 Ω
E7-4 (+S) or A38-13 (SPD) - Body ground Always 10 kΩ or higher



d.

Reconnect the ECM connector.


e.

Reconnect the combination meter connector.



OK

4.CHECK COMBINATION METER (+S VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

4.CHECK COMBINATION METER (+S VOLTAGE)
a.
U165844E01
1.589,2.018 1.856,2.178 0.267,0.161 10 E7 2.103,2.704 1.746,3.166 false 1.526,3.141 1.728,3.297 0.202,0.156 10 +S 0.115,0.066 0.299,0.240 0.185,0.174 10 *a

Disconnect the combination meter connector.

HINT:

Disconnect the ECU connectors on the other systems related to the speed signal (but the ECM connectors must be connected).



b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard voltage:
Tester Connection Switch Condition Specified Condition
E7-4 (+S) - Body ground Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*a Front view of wire harness connector
(to Combination Meter)



OK

5.CHECK COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM))

NG

5.CHECK COMBINATION METER (SPD SIGNAL OUTPUT WAVEFORM))
a.
A385088E01
0.156,0.802 0.49,1.021 0.333,0.219 2.031,1.656 1.49,1.385 true 0.104,0.104 0.354,0.302 0.25,0.198 10 false *a 0.24,0.823 0.479,0.99 0.24,0.167 10 false E7 2.104,1.594 2.396,1.792 0.292,0.198 10 false +S 0.417,2.969 0.76,3.167 0.344,0.198 10 false 5 V 0.427,3.938 0.771,4.135 0.344,0.198 10 false 0 V 1.688,4.125 2.719,4.375 1.031,0.25 10 false Turn Wheel

Disconnect the combination meter connector.


b.

Move the shift lever to the neutral position.


c.

Move the shift lever to the neutral position.


d.

Jack up one of the rear wheels.


e.

Turn the engine switch on (IG).


f.

Check the voltage between the terminal of the combination meter and the body ground while the rear wheel is turned slowly.

Tester Connection Condition Specified Condition
E7-4 (+S) - Body ground
·

Engine switch on (IG)

·

Wheel turned slowly


Voltage generated intermittently

Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter)



OK

NG

6.CHECK FOR COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
6.CHECK FOR COMBINATION METER ASSEMBLY (SPD SIGNAL INPUT WAVEFORM)
a.
A385088E02
0.156,0.833 0.49,1.063 0.333,0.229 1.969,1.604 1.531,1.365 true 0.25,0.854 0.563,1.052 0.313,0.198 10 false E7 2.042,1.583 2.354,1.781 0.313,0.198 10 false SI 0.469,2.958 0.781,3.156 0.313,0.198 10 false 5 V 0.438,3.948 0.75,4.146 0.313,0.198 10 false 0 V 1.667,4.156 2.677,4.375 1.01,0.219 10 false Turn Wheel

Disconnect the combination meter connector.


b.

Move the shift lever to the neutral position.


c.

Move the shift lever to the neutral position.


d.

Jack up one of the rear wheels.


e.

Turn the engine switch on (IG).


f.

Check the voltage between the terminal of the combination meter and the body ground while the rear wheel is turned slowly.

Tester Connection Condition Specified Condition
E7-3 (SI) - Body ground
·

Engine switch on (IG)

·

Wheel turned slowly


Voltage generated intermittently

Text in Illustration
*a Rear view of wire harness connector
(to Combination Meter)



OK

NG

7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)
7.CHECK HARNESS AND CONNECTOR (COMBINATION METER - SKID CONTROL ECU)
a.

Disconnect the combination meter connector.


b.

Disconnect the skid control ECU connector.


c.

Measure the resistance according the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
E7-3 (SI) - A24-12 (SP1) Always Below 1 Ω
E7-3 (SI) or A24-12 (SP1) - Body ground Always 10 kΩ or higher




OK

REPLACE MASTER CYLINDER SOLENOID

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR