Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2015.08–2016.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0504  Brake Switch "A" / "B" Correlation  


DESCRIPTION

The stop light switch is a duplex system that transmits two signals: STP and ST1-. These two signals are used by the ECM to monitor whether or not the brake system is working properly. If the signals, which indicate the brake pedal is being depressed and released, are detected simultaneously, the ECM interprets this as a malfunction in the stop light switch and stores the DTC.

HINT:

The normal conditions are as shown in the table below.

Signal (ECM Terminal) Brake Pedal Released In Transition Brake Pedal Depressed
STP OFF ON ON
ST1- ON ON OFF

·

[OFF] denotes ground potential.

·

[ON] denotes battery potential (+B).

·

On the GTS, both the Data List items Stop Light Switch and ST1 are ON when the brake pedal is depressed because the ST1 indication characteristic is opposite to the Stop Light Switch indication.



DTC No. DTC Detection Condition Trouble Area
P0504 Conditions (a), (b) and (c) continue for 0.5 seconds or more (1 trip detection logic):
(a) The engine switch is on (IG).
(b) The STP signal is OFF when the ST1- signal is OFF.
·

Short in stop light switch signal circuit

·

Stop light switch

·

ECM



WIRING DIAGRAM

A372453E02
2.99,3.469 3.115,3.635 0.125,0.167 10 false 1 2.938,3.646 3.198,3.823 0.26,0.177 10 false 1X 2.958,3.792 3.24,3.948 0.281,0.156 10 false *1 3.292,3.448 3.417,3.615 0.125,0.167 10 false 1 3.25,3.635 3.51,3.813 0.26,0.177 10 false 1Y 3.271,3.802 3.531,3.979 0.26,0.177 10 false *2 3.573,1.344 3.677,1.49 0.104,0.146 10 false 1 4.625,1.344 4.729,1.49 0.104,0.146 10 false 2 3.573,1.938 3.677,2.083 0.104,0.146 10 false 3 3.573,1.646 3.708,1.875 0.135,0.229 10 false 5 3.313,2.448 5.073,2.635 1.76,0.188 10 false Stop Light Switch Assembly 3.313,2.25 3.656,2.417 0.344,0.167 10 false A73 6.229,5.188 6.656,5.417 0.427,0.229 10 false ECM 5.938,1.344 6.26,1.521 0.323,0.177 10 false STP 5.958,1.938 6.313,2.125 0.354,0.188 10 false ST1- 5.677,1.344 5.948,1.542 0.271,0.198 10 false 36 5.677,1.927 6.073,2.156 0.396,0.229 10 false 35 5.958,4.99 6.885,5.177 0.927,0.188 10 false A52*1, A38*2 0.813,1.656 1.229,1.833 0.417,0.177 10 false STOP 1.917,1.938 2.667,2.198 0.75,0.26 10 false IG2 NO.1 4.844,4.073 5.083,4.24 0.24,0.167 10 false 1S 2.927,4.083 3.167,4.25 0.24,0.167 10 false 1R 0.729,3.875 1.094,4.042 0.365,0.167 10 false P/I-B 4.115,4.344 4.813,4.542 0.698,0.198 10 false IG2 MAIN 0.542,5.063 1.031,5.26 0.49,0.198 10 false Battery 3.573,4.781 5.042,4.958 1.469,0.177 10 false No. 2 Integration Relay 4.906,3.885 5.063,4.073 0.156,0.188 10 false 4 2.99,3.927 3.104,4.104 0.115,0.177 10 false 2 2,4.104 2.375,4.271 0.375,0.167 10 false IG1D 2.438,3.948 2.563,4.125 0.125,0.177 10 false 3 1.26,4.667 1.719,4.833 0.458,0.167 10 false E128 1.26,4.833 3.135,5.333 1.875,0.5 10 false Certification ECU Assembly (Smart Key ECU Assembly) 4.625,1.927 4.729,2.073 0.104,0.146 10 false 4 3.76,1.458 3.896,1.604 0.135,0.146 10 false B 3.74,1.75 3.875,1.979 0.135,0.229 10 false B 4.427,1.427 4.563,1.573 0.135,0.146 10 false L 4.427,2.01 4.563,2.167 0.135,0.156 10 false L 3.76,2.042 4.135,2.198 0.375,0.156 10 false GND 3.542,3.823 4.24,4.021 0.698,0.198 10 false IG2 MAIN 3.563,0.354 3.708,0.5 0.146,0.146 10 false 6 4.625,0.354 4.729,0.5 0.104,0.146 10 false 2 2.927,3.073 3.167,3.24 0.24,0.167 10 false 1R 2.979,2.885 3.094,3.063 0.115,0.177 10 false 1 3.365,0.906 5.146,1.156 1.781,0.25 10 false Stop Light Control Relay 3.365,0.76 3.708,0.927 0.344,0.167 10 false A39 3.781,0.479 4.156,0.635 0.375,0.156 10 false +B 4.25,0.49 4.625,0.646 0.375,0.156 10 false STP 3.333,5.135 4.229,5.302 0.896,0.167 10 false *1: for RHD 4.271,5.135 5.167,5.302 0.896,0.167 10 false *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following procedure.


HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Stop light switch conditions can be checked using the GTS.

(a)

Connect the GTS to the DLC3.

(b)

Turn the engine switch on (IG).

(c)

Turn the GTS on.

(d)

Enter the following menus: Powertrain / Engine and ECT / Data List / All Data / Stop Light Switch and ST1.

(e)

Check the Data List indication when the brake pedal is depressed and released.




Brake Pedal Operation Stop Light Switch ST1
Depressed ON ON
Released OFF OFF

PROCEDURE

1.READ VALUE USING GTS (STOP LIGHT SWITCH)
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.


d.

Enter the following menus: Powertrain / Engine and ECT / Data List / Stop Light Switch.


e.

Read the value displayed on the GTS.

OK:
Tester Display Measurement Item/Range (display) Normal Condition
Stop Light Switch Stop light switch status: ON or OFF ON: Brake pedal depressed
OFF: Brake pedal released




OK

NG

2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
2.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
U163581E01
0.586,1.87 0.906,2.059 0.320,0.189 10 A73 0.182,0.104 2.579,0.634 2.397,0.531 10 Front view of wire harness connector (to Stop Light Switch Assembly) 0.749,2.639 0.965,2.838 0.216,0.200 10 B 1.314,2.272 0.91,2.71 false

a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A73-1 (B) - Body ground Always 11 to 14 V




OK

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BATTERY)

3.CHECK TERMINAL VOLTAGE (POWER SOURCE OF STOP LIGHT SWITCH ASSEMBLY)
U163582E01
0.586,1.87 0.906,2.059 0.320,0.189 10 A73 0.182,0.104 2.579,0.634 2.397,0.531 10 Front view of wire harness connector (to Stop Light Switch Assembly) 2.476,2.51 2.693,2.710 0.216,0.200 10 B 2.156,2.28 2.431,2.564 false

a.

Disconnect the stop light switch assembly connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
A73-5 (B) - Body ground Engine switch on (IG) 11 to 14 V




OK

4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)

NG

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 2 INTEGRATION RELAY)
4.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - BODY GROUND)
a.

Disconnect the stop light switch assembly connector.


b.

Measure the Resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Switch Condition Specified Condition
A73-3 (GND) - Body ground Always Below 1 Ω




OK

5.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

5.CHECK TERMINAL VOLTAGE (STP AND ST1- VOLTAGE)
U163767E02
5.604,0.917 5.24,1.396 false 5.708,0.917 5.99,1.385 false 0.521,1.323 2.188,1.573 1.667,0.25 10 false Brake Pedal Depressed 2.302,1.354 3.969,1.604 1.667,0.25 10 false Brake Pedal Released 4.073,0.063 6.948,0.302 2.875,0.24 10 false Component with harness connected (ECM) 5.698,1.417 6.396,1.656 0.698,0.24 10 false 36 (STP) 4.969,1.427 5.667,1.667 0.698,0.24 10 false 35 (ST-) 4.146,0.885 4.51,1.073 0.365,0.188 10 false A38 6.333,0.604 7.125,0.771 0.792,0.167 10 false *1: for RHD 6.333,0.958 7.104,1.125 0.771,0.167 10 false *2: for LHD 4.135,0.531 4.5,0.719 0.365,0.188 10 false A52 4.521,0.406 4.76,0.604 0.24,0.198 10 false *1 4.521,0.76 4.75,0.938 0.229,0.177 10 false *2

a.

Disconnect the ECM connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage (for RHD):
Tester Connection Brake Pedal Operation Specified Condition
A52-35 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V
A52-36 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V


Standard Voltage (for LHD):
Tester Connection Brake Pedal Operation Specified Condition
A38-35 (ST1-) - Body ground Released 7.5 to 14 V
Depressed Below 1.5 V
A38-36 (STP) - Body ground Released Below 1.5 V
Depressed 7.5 to 14 V




OK

NG

6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
6.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - ECM)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the Resistance according to the value(s) in the table below.

Standard Resistance (for RHD):
Tester Connection Brake Pedal Operation Specified Condition
A73-4 (L) - A52-35 (ST1-) Always Below 1 Ω
A73-2 (L) - A52-36 (STP) Always Below 1 Ω
A73-4 (L) or A52-35 (ST1-) - Body ground Always 10 kΩ or higher
A73-2 (L) or A52-36 (STP) - Body ground Always 10 kΩ or higher


Standard Resistance (for LHD):
Tester Connection Brake Pedal Operation Specified Condition
A73-4 (L) - A38-35 (ST1-) Always Below 1 Ω
A73-2 (L) - A38-36 (STP) Always Below 1 Ω
A73-4 (L) or A38-35 (ST1-) - Body ground Always 10 kΩ or higher
A73-2 (L) or A38-36 (STP) - Body ground Always 10 kΩ or higher




OK

REPLACE STOP LIGHT SWITCH ASSEMBLY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

7.CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH ASSEMBLY - NO. 2 INTEGRATION RELAY)
a.

Disconnect the stop light switch assembly connector.


b.

Disconnect the No. 2 integration relay connector.


c.

Measure the Resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Brake Pedal Operation Specified Condition
A73-5 (B) - 1R-1 Always Below 1 Ω
A73-5 (B) or 1R-1 - Body ground Always 10 kΩ or higher




OK

REPLACE NO. 2 INTEGRATION RELAY

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR