Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0010  Camshaft Position "A" Actuator Circuit (Bank 1)  P0020  Camshaft Position "A" Actuator Circuit (Bank 2)  


DESCRIPTION

·

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (variable valve timing) system adjusts the intake and exhaust valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 V to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E17
4.483,0.815 5.290,0.978 0.807,0.163 10 VVT Sensor 4.483,1.325 6.216,1.485 1.733,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.802,3.922 2.203,0.174 10 Camshaft Timing Oil Control Valve 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty Cycle 4.483,1.827 5.808,1.981 1.325,0.154 10 Mass Air Flow Meter 4.483,2.854 6.827,3.042 2.344,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.031,2.511 1.547,0.167 10 Throttle Position Sensor 4.483,3.353 5.938,3.506 1.455,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 5.098,4.400 1.438,0.184 10 Camshaft Timing Gear 3.883,4.917 4.984,5.101 1.100,0.184 10 Intake Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0010 Open or short in the camshaft timing oil control valve for intake side (for Bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve for intake side (for Bank 1) circuit

·

Camshaft timing oil control valve assembly for intake side (for Bank 1)

·

ECM


P0020 Open or short in the camshaft timing oil control valve for intake side (for Bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve for intake side (for Bank 2) circuit

·

Camshaft timing oil control valve assembly for intake side (for Bank 2)

·

ECM



HINT:

These DTCs relate to the camshaft timing oil control valve.


MONITOR DESCRIPTION

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

The monitor for this DTC runs 5 seconds after the engine switch is turned on (IG).

CONFIRMATION DRIVING PATTERN

1.

Turn the engine switch on (IG) and wait for 5 seconds or more.


WIRING DIAGRAM

U163113E01
5.855,4.134 6.206,4.318 0.350,0.184 10 ECM 5.408,0.515 5.842,0.671 0.434,0.156 10 OC1+ 5.408,1.243 5.842,1.399 0.434,0.156 10 OC1- 5.408,2.49 5.842,2.646 0.434,0.156 10 OC2+ 5.408,3.219 5.842,3.375 0.434,0.156 10 OC2- 0.089,1.64 4.563,1.842 4.474,0.202 10 Camshaft Timing Oil Control Valve Assembly (for Intake Side of Bank 1) 0.089,3.626 4.572,3.827 4.483,0.201 10 Camshaft Timing Oil Control Valve Assembly (for Intake Side of Bank 2) 0.089,1.458 0.469,1.623 0.380,0.165 10 C27 0.089,3.457 0.450,3.622 0.361,0.165 10 C28 1.453,0.5 1.579,0.690 0.126,0.191 10 1 1.46,1.238 1.579,1.411 0.119,0.173 10 2 1.453,2.453 1.579,2.644 0.126,0.191 10 1 1.46,3.191 1.579,3.365 0.119,0.173 10 2 5.059,3.147 5.386,3.303 0.327,0.156 10 51*2 5.059,2.409 5.377,2.565 0.318,0.156 10 52*2 5.059,1.176 5.374,1.332 0.315,0.156 10 57*2 5.059,0.438 5.369,0.594 0.310,0.156 10 58*2 5.073,0.602 5.371,0.744 0.298,0.142 10 C45 5.073,1.341 5.371,1.483 0.298,0.142 10 C45 5.073,2.573 5.371,2.716 0.298,0.142 10 C45 5.073,3.316 5.371,3.458 0.298,0.142 10 C45 4.717,3.146 5.035,3.302 0.318,0.156 10 51*1 4.717,2.409 5.035,2.564 0.318,0.156 10 52*1 4.717,1.176 5.044,1.332 0.327,0.156 10 57*1 4.717,0.438 5.026,0.594 0.309,0.156 10 58*1 4.744,0.6 5.043,0.745 0.299,0.145 10 C46 4.745,1.34 5.043,1.482 0.298,0.142 10 C46 4.745,2.573 5.043,2.715 0.298,0.142 10 C46 4.745,3.316 5.043,3.458 0.298,0.142 10 C46 1.11,4.148 1.877,4.327 0.767,0.179 10 *1: for RHD 1.11,4.391 1.840,4.552 0.730,0.161 10 *2: for LHD

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK FOR DTC
a.

Clear the DTCs after recording the freeze frame data and DTCs (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).


b.

Turn the engine switch off.


c.

Start the engine and allow it to idle. Then check for DTCs.


d.

Check that P0010 or P0020 is not output.

OK:

P0010 or P0020 is not output.




OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)
a.

Disconnect the camshaft timing oil control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C27-1 - C46-58 (OC1+) Always Below 1 Ω
C28-1 - C46-52 (OC2+) Always Below 1 Ω
C27-2 - C46-57 (OC1-) Always Below 1 Ω
C28-2 - C46-51 (OC2-) Always Below 1 Ω
C27-1 or C46-58 (OC1+) - Body ground Always 10 kΩ or higher
C28-1 or C46-52 (OC2+) - Body ground Always 10 kΩ or higher
C27-2 or C46-57 (OC1-) - Body ground Always 10 kΩ or higher
C28-2 or C46-51 (OC2-) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C27-1 - C45-58 (OC1+) Always Below 1 Ω
C28-1 - C45-52 (OC2+) Always Below 1 Ω
C27-2 - C45-57 (OC1-) Always Below 1 Ω
C28-2 - C45-51 (OC2-) Always Below 1 Ω
C27-1 or C45-58 (OC1+) - Body ground Always 10 kΩ or higher
C28-1 or C45-52 (OC2+) - Body ground Always 10 kΩ or higher
C27-2 or C45-57 (OC1-) - Body ground Always 10 kΩ or higher
C28-2 or C45-51 (OC2-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR