Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0660  Intake Manifold Tuning Valve Control Circuit / Open (Bank 1)  


DESCRIPTION

This circuit opens and closes the Intake Air Control Valve (IACV) in response to the engine load in order to increase the intake efficiency (ACIS: Acoustic Control Induction System).

A233285E01
0.066,0.262 1.048,0.439 0.982,0.177 10 Intake Manifold 1.039,0.339 1.419,0.812 false 2.171,0.427 2.556,0.590 0.385,0.163 10 IACV 2.139,0.493 1.856,1.064 false 2.791,2.441 3.141,2.611 0.350,0.170 10 ECM 3.554,2.529 5.078,2.692 1.524,0.163 10 Throttle Position Sensor 2.153,3.107 3.885,3.270 1.732,0.163 10 Crankshaft Position Sensor 5.134,1.269 5.607,1.439 0.473,0.170 10 Closed 5.074,0.073 5.487,0.250 0.413,0.177 10 Open 2.868,0.164 4.676,0.355 1.809,0.191 10 Throttle Valve Position (deg.) 5.817,1.883 7.098,2.080 1.281,0.198 10 Engine Speed (rpm) 5.461,0.152 5.573,0.152 5.573,0.152 6.223,0.795 false 6.077,0.41 6.077,0.349 false 4.739,1.087 4.682,1.087 false 5.915,0.195 6.265,0.364 0.350,0.170 10 4350 4.5,1.015 4.680,1.167 0.180,0.152 10 50

DTC No. DTC Detection Condition Trouble Area
P0660 The following conditions are met simultaneously for 0.5 seconds or more (2 trip detection logic):
1.

Voltage of acoustic control induction system terminal of the ECM is low when the actuator is off.

2.

The engine has been started.


·

Open or short in intake air control valve circuit

·

Intake air surge tank assembly (intake air control valve assembly)

·

ECM



WIRING DIAGRAM

U163723E01
1.192,0.506 1.829,0.671 0.637,0.165 10 EFI NO. 2 2.643,0.665 3.042,0.830 0.399,0.165 10 C129 2.566,0.273 2.685,0.440 0.119,0.167 10 1 3.345,0.273 3.464,0.440 0.119,0.167 10 2 5.186,2.01 5.486,2.166 0.299,0.156 10 A38 5.174,1.822 5.488,1.987 0.314,0.165 10 34*2 5.521,0.492 5.918,0.657 0.397,0.165 10 ACIS 5.185,0.385 5.484,0.541 0.299,0.156 10 C45 5.174,0.197 5.515,0.362 0.341,0.165 10 62*2 5.526,2.102 5.969,2.267 0.443,0.165 10 MREL 4.461,1.459 4.580,1.624 0.119,0.165 10 4 4.42,1.648 4.650,1.814 0.230,0.165 10 1B 4.475,1.849 4.594,2.014 0.119,0.165 10 2 4.42,2.01 4.650,2.175 0.230,0.165 10 1B 2.677,1.459 2.796,1.624 0.119,0.165 10 1 2.636,1.648 2.866,1.814 0.230,0.165 10 1C 2.677,1.849 2.796,2.014 0.119,0.165 10 3 2.636,2.01 2.866,2.175 0.230,0.165 10 1B 2.925,1.777 3.587,1.935 0.663,0.158 10 EFI MAIN 3.773,2.328 4.038,2.493 0.265,0.165 10 EFI 2.878,2.757 4.393,2.941 1.515,0.184 10 No. 1 Integration Relay 0.814,2.505 1.303,2.707 0.489,0.202 10 Battery 1.184,0.253 1.303,0.420 0.119,0.167 10 1 1.724,0.253 1.843,0.420 0.119,0.167 10 2 5.965,3.061 6.308,3.203 0.343,0.142 10 ECM 2.623,0.812 4.918,0.975 2.295,0.163 10 Vacuum Switching Valve (for ACIS) 4.857,2.01 5.157,2.166 0.299,0.156 10 A52 4.845,1.822 5.159,1.987 0.314,0.165 10 34*1 4.856,0.385 5.155,0.541 0.299,0.156 10 C46 4.845,0.197 5.186,0.362 0.341,0.165 10 62*1 3.8,3.187 4.553,3.364 0.753,0.177 10 *1: for RHD 3.8,3.453 4.553,3.630 0.753,0.177 10 *2: for LHD

CAUTION / NOTICE / HINT

NOTICE:

Inspect the fuses for circuits related to this system before performing the following inspection procedure.


HINT:

Read freeze frame data using the GTS. The ECM records vehicle and driving condition information as freeze frame data the moment a DTC is stored. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.


PROCEDURE

1.PERFORM ACTIVE TEST USING GTS (OPERATE VSV FOR ACIS)
A233358E01
0.235,0.261 0.443,0.424 0.208,0.163 10 *a 0.297,2.646 0.482,2.793 0.185,0.147 10 *b 1.242,0.985 1.387,1.144 0.145,0.159 10 E 1.044,3.125 1.190,3.284 0.145,0.159 10 E 1.111,1.245 1.225,1.401 0.114,0.156 10 F 0.916,3.387 1.030,3.542 0.114,0.156 10 F 1.021,0.467 1.198,0.637 0.177,0.170 10 *c 0.54,1.597 0.716,1.767 0.177,0.170 10 *c 1.141,2.62 1.318,2.790 0.177,0.170 10 *c 2.585,2.972 2.762,3.142 0.177,0.170 10 *c

a.

Disconnect the vacuum hose from port F on the vacuum switching valve (for ACIS).


b.

Connect the GTS to the DLC3.


c.

Start the engine.


d.

Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Intake Control.


e.

Operate the VSV for ACIS.


f.

Check the VSV air flow when switching the VSV.

OK:
Test Condition Specified Condition
VSV is ON Air from port E flows out through port F
VSV is OFF Air from port E flows out through air filter


Text in Illustration
*a VSV is ON
*b VSV is OFF
*c Air



OK

NG

2.INSPECT VACUUM SWITCHING VALVE (FOR ACIS)
2.INSPECT VACUUM SWITCHING VALVE (FOR ACIS)

OK

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE VOLTAGE)

NG

REPLACE VACUUM SWITCHING VALVE(FOR ACIS)

3.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE VOLTAGE)
a.
U163332E02
0.219,0.104 0.417,0.281 0.198,0.177 10 false *a 0.594,1.073 0.99,1.302 0.396,0.229 10 false C129

Disconnect the intake air control valve assembly connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
C129-1 - Body ground Engine switch on (IG) 11 to 14 V


Text in Illustration
*a Front view of wire harness connector
(to Intake Air Control Valve Assembly)


d.

Reconnect the intake air control valve assembly connector.



OK

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (EFI MAIN RELAY - VACUUM SWITCHING VALVE)

4.CHECK HARNESS AND CONNECTOR (VACUUM SWITCHING VALVE - ECM)
a.

Disconnect the intake air control valve assembly connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C129-2 - C46-62 (ACIS) Always Below 1 Ω
C129-2 or C46-62 (ACIS) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C129-2 - C45-62 (ACIS) Always Below 1 Ω
C129-2 or C45-62 (ACIS) - Body ground Always 10 kΩ or higher



d.

Reconnect the intake air control valve assembly connector.


e.

Reconnect the ECM connector.



OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR (VACUUM SWITCHING VALVE - ECM)