Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P2431  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank1  P2432  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank1  P2433  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank1  P2436  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Range / Performance Bank 2  P2437  Secondary Air Injection System Air Flow / Pressure Sensor Circuit Low Bank 2  P2438  Secondary Air Injection System Air Flow / Pressure Sensor Circuit High Bank 2  


DESCRIPTION

Refer to DTC P0412 (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0412).

Refer to DTC P0416 (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>P0416).

DTC No. DTC Detection Condition Trouble Area
P2431
P2436
Pressure sensor indicates a value below 45.6 kPa (342 mmHg), or higher than 135 kPa (1013 mmHg) (2 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


P2432
P2437
While the engine is running, the voltage output of the pressure sensor is below 0.5 V (1 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM


P2433
P2438
While the engine is running, the voltage output of the pressure sensor is higher than 4.5 V (1 trip detection logic).
·

Pressure sensor

·

Open or short in pressure sensor circuit

·

ECM



MONITOR DESCRIPTION

A085160E38
0.073,2.771 1.125,2.948 1.052,0.177 10 false Pressure Sensor 2.594,2.927 2.917,3.104 0.323,0.177 10 false ECM 2.292,0.833 2.688,1.01 0.396,0.177 10 false VCV1 2.292,1.479 2.531,1.656 0.24,0.177 10 false AIP 0.833,1.615 1.073,1.792 0.24,0.177 10 false AIP 2.292,2.094 2.5,2.271 0.208,0.177 10 false E2 0.865,1.031 1.073,1.208 0.208,0.177 10 false VC 0.875,2.208 1.063,2.385 0.188,0.177 10 false E2 0.083,0.042 2.156,0.271 2.073,0.229 10 false Reference (for Bank 1):

The ECM monitors the pressure in the secondary air passage using the pressure sensor located on the air switching valve in the secondary air injection system. Using this pressure value, the ECM determines whether the secondary air injection system is malfunctioning or not.

If there is a defect in the sensor or the sensor circuit, the voltage level deviates from the normal operating range. The ECM interprets this deviation as a malfunction in the pressure sensor or circuit and stores a DTC.

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the Secondary Air Injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While Secondary Air Injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the engine switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the engine switch on (IG).

5.

Turn the GTS on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

7.

Turn the engine switch off and wait for at least 30 seconds.

8.

Turn the engine switch on (IG) and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air Injection Check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the Secondary Air Injection system pending codes: Press ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After "Secondary Air Injection Check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P2431, P2432, P2433, P2436, P2437 or P2438.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the engine switch off.


WIRING DIAGRAM

U162879E01
1.323,1.192 1.556,1.362 0.232,0.170 10 VC 1.665,2.489 1.815,2.638 0.149,0.149 10 4 1.281,1.76 1.555,1.930 0.274,0.170 10 AIP 5.655,1.192 6.063,1.362 0.408,0.170 10 VCV1 5.655,1.76 5.929,1.930 0.274,0.170 10 AIP 1.344,2.313 1.556,2.483 0.211,0.170 10 E2 0.32,2.783 0.679,2.950 0.359,0.168 10 C137 0.32,2.952 2.232,3.277 1.912,0.325 10 Air Switching Valve Assembly (for Bank 1) 1.274,3.714 1.636,3.884 0.362,0.170 10 VC2 1.223,4.282 1.555,4.451 0.332,0.170 10 AIP2 1.251,4.835 1.555,5.005 0.304,0.170 10 E22 0.32,5.346 0.688,5.514 0.368,0.168 10 C138 0.32,5.516 2.352,5.850 2.033,0.335 10 Air Switching Valve Assembly (for Bank 2) 5.298,1.104 5.602,1.283 0.304,0.179 10 67*2 5.306,1.273 5.593,1.430 0.288,0.157 10 C45 5.298,1.678 5.620,1.857 0.323,0.179 10 54*2 5.306,1.843 5.593,1.999 0.288,0.157 10 A38 5.655,4.282 6.003,4.451 0.348,0.170 10 AIP2 5.295,4.2 5.608,4.378 0.313,0.179 10 53*2 5.306,4.365 5.593,4.521 0.288,0.157 10 A38 5.655,4.827 5.857,4.997 0.202,0.170 10 E2 6.053,5.804 6.428,5.973 0.376,0.170 10 ECM 5.295,4.745 5.604,4.924 0.309,0.179 10 98*2 5.306,4.91 5.593,5.067 0.288,0.157 10 C45 1.665,1.368 1.815,1.518 0.149,0.149 10 2 1.665,1.936 1.815,2.085 0.149,0.149 10 3 1.661,5.006 1.810,5.156 0.149,0.149 10 4 1.661,3.886 1.810,4.035 0.149,0.149 10 2 1.661,4.453 1.810,4.602 0.149,0.149 10 3 4.961,1.104 5.266,1.283 0.304,0.179 10 67*1 4.969,1.273 5.257,1.430 0.288,0.157 10 C46 4.961,1.678 5.284,1.857 0.323,0.179 10 54*1 4.969,1.843 5.257,1.999 0.288,0.157 10 A52 4.959,4.2 5.272,4.378 0.313,0.179 10 53*1 4.969,4.365 5.257,4.521 0.288,0.157 10 A52 4.959,4.745 5.268,4.924 0.309,0.179 10 98*1 4.969,4.91 5.257,5.067 0.288,0.157 10 C46 3.119,5.341 3.886,5.516 0.767,0.174 10 *1: for RHD 3.119,5.612 3.886,5.786 0.767,0.174 10 *2: for LHD

CAUTION / NOTICE / HINT

HINT:
·

Refer to "Data List / Active Test" [Air Pump Pressure (Absolute) and Air Pump2 Pressure (Absolute)] (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DATA LIST / ACTIVE TEST).

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (PRESSURE SENSOR - ECM)
a.

Disconnect the air switching valve connector.


b.

Disconnect the ECM connectors.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C137-3 (AIP) - A52-54 (AIP) Always Below 1 Ω
C137-2 (VC) - C46-67 (VCV1) Always Below 1 Ω
C137-4 (E2) - C46-98 (E2) Always Below 1 Ω
C138-3 (AIP2) - A52-53 (AIP2) Always Below 1 Ω
C138-2 (VC2) - C46-67 (VCV1) Always Below 1 Ω
C138-4 (E22) - C46-98 (E2) Always Below 1 Ω
C137-3 (AIP) or A52-54 (AIP) - Body ground Always 10 kΩ or higher
C137-2 (VC) or C46-67 (VCV1) - Body ground Always 10 kΩ or higher
C138-3 (AIP2) or A52-53 (AIP2) - Body ground Always 10 kΩ or higher
C138-2 (VC2) or C46-67 (VCV1) - Body ground Always 10 kΩ or higher


Standard Resistance:
for LHD
Tester Connection Condition Specified Condition
C137-3 (AIP) - A38-54 (AIP) Always Below 1 Ω
C137-2 (VC) - C45-67 (VCV1) Always Below 1 Ω
C137-4 (E2) - C45-98 (E2) Always Below 1 Ω
C138-3 (AIP2) - A38-53 (AIP2) Always Below 1 Ω
C138-2 (VC2) - C45-67 (VCV1) Always Below 1 Ω
C138-4 (E22) - C45-98 (E2) Always Below 1 Ω
C137-3 (AIP) or A38-54 (AIP) - Body ground Always 10 kΩ or higher
C137-2 (VC) or C45-67 (VCV1) - Body ground Always 10 kΩ or higher
C138-3 (AIP2) or A38-53 (AIP2) - Body ground Always 10 kΩ or higher
C138-2 (VC2) or C45-67 (VCV1) - Body ground Always 10 kΩ or higher




OK

2.CHECK TERMINAL VOLTAGE (VC OF AIR SWITCHING VALVE)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK TERMINAL VOLTAGE (VC OF AIR SWITCHING VALVE)
U163333E02
1.542,1.135 0.969,1.646 false 1.844,1.135 2.094,1.656 false 0.188,0.146 0.396,0.333 0.208,0.188 10 false *a 0.188,0.875 0.563,1.042 0.375,0.167 10 false C137 0.188,1.25 0.552,1.417 0.365,0.167 10 false C138 0.708,0.865 0.906,1.042 0.198,0.177 10 false *A 0.708,1.25 0.906,1.427 0.198,0.177 10 false *B 0.781,1.677 1.156,1.833 0.375,0.156 10 false VC*A 0.781,1.896 1.219,2.052 0.438,0.156 10 false VC2*B 2.01,1.677 2.385,1.833 0.375,0.156 10 false E2*A 2.01,1.896 2.448,2.052 0.438,0.156 10 false E22*B

a.

Disconnect the air switching valve connector.


b.

Turn the engine switch on (IG).


c.

Measure the voltage according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C137-2 (VC) - C137-4 (E2) Engine switch on (IG) 4.5 to 5.5 V
C138-2 (VC2) - C138-4 (E22) Engine switch on (IG) 4.5 to 5.5 V


Text in Illustration
*A Bank 1
*B Bank 2
*a Front view of wire harness connector
(to Air Switching Valve Assembly)



OK

3.REPLACE AIR SWITCHING VALVE ASSEMBLY

NG

3.REPLACE AIR SWITCHING VALVE ASSEMBLY
a.

Replace the air switching valve assembly.

HINT:
·

Replace the air switching valve assembly for bank 1 (See page Engine / Hybrid System>1UR-FE (EMISSION CONTROL)>AIR SWITCHING VALVE(for Bank 1)>REMOVAL).

·

Replace the air switching valve assembly for bank 2 (See page Engine / Hybrid System>1UR-FE (EMISSION CONTROL)>AIR SWITCHING VALVE (for Bank 2)>REMOVAL).





NEXT

4.CHECK WHETHER DTC OUTPUT RECURS
4.CHECK WHETHER DTC OUTPUT RECURS
a.

Perform the Confirmation Driving Pattern.

Result
Display (DTC Output) Proceed to
NORMAL
(No DTC output)
A
ABNORMAL
(P2431, P2432, P2433, P2436, P2437 or P2438 output)
B



A

END

B