Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0412  Secondary Air Injection System Switching Valve "A" Circuit  


DESCRIPTION

The secondary air injection system injects air into the exhaust port of the cylinder head using an electric air pump, starting when the engine is started cold and operating until the catalyst warms up, in order to promote combustion of unburned fuel and decrease the amount of hydrocarbons (HC) and carbon monoxide (CO) in the exhaust gas.

A217752E03
3.306,0.35 3.777,0.523 0.471,0.173 10 ECM 1.955,0.91 2.858,1.265 0.903,0.354 10 Air Injection Control Driver 0.18,1.802 2.072,2.020 1.893,0.218 10 Pressure Sensor (for Bank 1) 0.146,2.706 1.585,3.100 1.439,0.394 10 Air Switching Valve Assembly (for Bank 1) 5.781,2.964 7.059,3.163 1.278,0.199 10 Air Pump Assembly 0.062,4.838 1.339,5.218 1.277,0.379 10 Heated Oxygen Sensor (for Bank 1) 0.048,3.907 1.403,4.265 1.355,0.358 10 Air Fuel Ratio Sensor (for Bank 1) 3.681,0.986 4.133,1.178 0.452,0.192 10 Relay 5.267,0.965 6.387,1.295 1.119,0.330 10 Pressure Sensor (for Bank 2) 5.733,3.345 7.162,3.733 1.428,0.387 10 Air Switching Valve Assembly (for Bank 2) 5.859,5.239 7.109,5.582 1.250,0.343 10 Heated Oxygen Sensor (for Bank 2) 5.859,4.467 7.128,4.812 1.268,0.345 10 Air Fuel Ratio Sensor (for Bank 2) 4.119,1.071 4.288,1.071 false 5.216,1.015 5.132,1.015 5.132,1.015 4.719,2.505 false 2.072,1.897 2.337,1.897 2.337,1.897 2.561,2.505 false 1.427,2.794 1.84,2.794 false 1.536,3.988 1.397,3.988 false 1.536,4.934 1.28,4.934 false 5.658,3.404 5.558,3.404 5.558,3.404 5.279,3.205 false 5.812,4.545 5.714,4.545 5.714,4.545 5.574,3.984 false 5.812,5.302 5.644,5.302 5.644,5.302 5.553,4.938 false 6.426,2.941 6.426,2.773 false

DTC No. DTC Detection Condition Trouble Area
P0412 All conditions are met for 3 seconds or more while idling immediately after the engine is started (1 trip detection logic):
·

Secondary air injection system is not operating (the air pump and air switching valve are off).

·

Diagnostic signal from the air injection control driver has a duty cycle of 40% (this indicates an open in the air switching valve circuit).

·

Battery voltage is 8 V or higher.


·

Open in air switching valve drive circuit

·

Air injection control driver

·

Air switching valve assembly

·

ECM


P0412 All conditions are met for 3 seconds or more while idling immediately after the engine is started (1 trip detection logic):
·

Secondary air injection system is operating (the air pump and air switching valve are on).

·

Diagnostic signal from the air injection control driver has a duty cycle of 40% (this indicates a short in the air switching valve circuit).

·

Battery voltage is 8 V or higher.


·

Short between air switching valve drive circuit and body ground

·

Air injection control driver

·

Air switching valve assembly

·

ECM



MONITOR DESCRIPTION

This DTC indicates an open or short circuit in the circuit containing the air switching valve of the secondary air injection system. The air injection control driver performs diagnosis of the air pump, air switching valve (bank 1) and itself, and sends the results of this diagnosis to the ECM as a duty signal. When the ECM receives a signal indicating a malfunction in the air pump, air switching valve or air injection control driver, it illuminates the MIL and stores a DTC.

CONFIRMATION DRIVING PATTERN

NOTICE:
·

This Secondary Air Injection Check only allows technicians to operate the secondary air injection system for a maximum of 5 seconds. Furthermore, the check can only be performed up to 4 times per trip. If the test is repeated, intervals of at least 30 seconds are required between checks. While secondary air injection system operation using the GTS is prohibited, the GTS display indicates the prohibition (WAIT or ERROR). If ERROR is displayed on the GTS during the test, stop the engine for 10 minutes, and then try again.

·

Performing Secondary Air Injection Check repeatedly may cause damage to the secondary air injection system. If it is necessary to repeat the check, leave an interval of several minutes between System Check operations to prevent the system from overheating.

·

When performing the Secondary Air Injection Check operation after the battery cable has been reconnected, wait for 7 minutes with the engine switch turned on (IG) or the engine running.

·

Turn the engine switch off when the Secondary Air Injection Check operation finishes.



1.

Start the engine and warm it up.

2.

Turn the engine switch off.

3.

Connect the GTS to the DLC3.

4.

Turn the engine switch on (IG).

5.

Turn the GTS on.

6.

Clear DTCs (even if no DTCs are stored, perform the clear DTC operation) (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>SFI SYSTEM>DTC CHECK / CLEAR).

7.

Turn the engine switch off and wait for at least 30 seconds.

8.

Turn the engine switch on (IG) and turn the GTS on.

9.

Enter the following menus: Powertrain / Engine and ECT / Utility / Secondary Air injection check / Automatic Mode.

10.

Start the engine after the GTS initialization is finished.

11.

Perform the System Check operation by pressing ENTER (Next).

12.

Perform the following to confirm the secondary air injection system pending codes: Press ENTER (Exit).

13.

Check for pending DTCs.

OK:

No pending DTC is output.


14.

After "Secondary Air injection check" is completed, check for All Readiness by entering the following menus: Powertrain / Engine and ECT / Utility / All Readiness.

15.

Input the DTC: P0412.

16.

Check the DTC judgment result.

GTS Display Description
NORMAL
·

DTC judgment completed

·

System normal


ABNORMAL
·

DTC judgment completed

·

System abnormal


INCOMPLETE
·

DTC judgment not completed

·

Perform driving pattern after confirming DTC enabling conditions


N/A
·

Unable to perform DTC judgment

·

Number of DTCs which do not fulfill DTC preconditions has reached ECU memory limit



HINT:
·

If the judgment result shows NORMAL, the system is normal.

·

If the judgment result shows ABNORMAL, the system has a malfunction.



17.

Turn the engine switch off.


WIRING DIAGRAM

U163747E02
5.979,1 6.375,1.146 0.396,0.146 10 false A38 5.948,4.854 6.271,5.104 0.323,0.25 10 false A38 5.979,1.635 6.406,1.781 0.427,0.146 10 false C45 5.979,2.906 6.406,3.052 0.427,0.146 10 false C45 5.969,6.167 6.302,6.313 0.333,0.146 10 false C45 6.01,2.281 6.438,2.427 0.427,0.146 10 false C45 5.958,5.51 6.292,5.656 0.333,0.146 10 false C45 5.969,0.813 6.313,0.979 0.344,0.167 10 false 34*4 5.969,1.448 6.313,1.604 0.344,0.156 10 false 30*4 5.958,2.104 6.302,2.26 0.344,0.156 10 false 28*4 5.969,2.667 6.313,2.823 0.344,0.156 10 false 54*4 5.969,5.333 6.313,5.49 0.344,0.156 10 false 67*4 5.969,4.667 6.333,4.833 0.365,0.167 10 false 54*4 5.938,5.979 6.26,6.146 0.323,0.167 10 false 98*4 6.323,1.031 6.906,1.208 0.583,0.177 10 false MREL 6.333,1.594 6.76,1.771 0.427,0.177 10 false AIDI 6.323,2.292 6.76,2.469 0.438,0.177 10 false AIRV 6.323,2.906 6.75,3.083 0.427,0.177 10 false AIRP 6.323,4.833 6.604,5.01 0.281,0.177 10 false AIP 6.323,5.479 6.813,5.656 0.49,0.177 10 false VCV1 6.323,6.156 6.813,6.333 0.49,0.177 10 false E2 4.698,4.594 4.948,4.792 0.25,0.198 10 false +B 4.844,5.5 5.094,5.677 0.25,0.177 10 false VC 4.896,6.167 5.146,6.344 0.25,0.177 10 false E2 4.479,6.427 4.813,6.615 0.333,0.188 10 false GND 5.156,1.635 5.51,1.823 0.354,0.188 10 false C61 3.99,1.635 4.292,1.823 0.302,0.188 10 false C61 5.146,2.281 5.5,2.469 0.354,0.188 10 false C61 5.146,2.885 5.5,3.073 0.354,0.188 10 false C61 3.99,3.198 4.292,3.385 0.302,0.188 10 false C60 4.635,3.625 4.938,3.813 0.302,0.188 10 false C61 3.979,2.156 4.313,2.365 0.333,0.208 10 false C61 3.979,2.688 4.281,2.875 0.302,0.188 10 false C60 5.25,1.448 5.438,1.594 0.188,0.146 10 false 2 5.24,2.073 5.427,2.219 0.188,0.146 10 false 3 5.24,2.677 5.427,2.823 0.188,0.146 10 false 4 4.448,3.615 4.604,3.76 0.156,0.146 10 false 6 4.042,2.479 4.219,2.635 0.177,0.156 10 false 1 4.063,1.927 4.219,2.073 0.156,0.146 10 false 1 4.073,3.01 4.229,3.156 0.156,0.146 10 false 2 4.083,1.438 4.219,1.583 0.135,0.146 10 false 5 4.323,1.604 4.552,1.802 0.229,0.198 10 false +B 4.323,2.667 4.74,2.844 0.417,0.177 10 false BATT 4.323,3.146 4.552,3.323 0.229,0.177 10 false VP 4.344,2.167 4.573,2.344 0.229,0.177 10 false E 4.656,3.385 4.885,3.563 0.229,0.177 10 false VV 3.031,1.792 3.656,1.99 0.625,0.198 10 false EFI NO.2 1.365,2.906 2.292,3.052 0.927,0.146 10 false A/PMP NO.1 0.74,1.635 0.938,1.802 0.198,0.167 10 false 1C 0.75,1.875 0.885,2.021 0.135,0.146 10 false 1 1.854,1.969 2.146,2.125 0.292,0.156 10 false EFI 1.24,1.802 1.563,1.979 0.323,0.177 10 false EFI 2.479,1.625 2.677,1.792 0.198,0.167 10 false 1B 2.49,1 2.688,1.167 0.198,0.167 10 false 1B 0.74,1.01 0.938,1.177 0.198,0.167 10 false 1B 2.5,1.844 2.635,1.99 0.135,0.146 10 false 4 2.521,0.813 2.656,0.958 0.135,0.146 10 false 2 0.75,0.802 0.885,0.948 0.135,0.146 10 false 3 1.625,6.667 1.979,6.823 0.354,0.156 10 false C139 0.823,2.25 2.615,2.406 1.792,0.156 10 false No. 1 Integration Relay 1.583,6.844 2.323,7.052 0.74,0.208 10 false Air Pump*1 4.01,7.063 4.385,7.219 0.375,0.156 10 false C137 2.052,3.917 3.01,4.094 0.958,0.177 10 false AI PMP HTR*5 2.052,3.646 2.979,3.833 0.927,0.188 10 false AI-PUMP HTR 0.406,3.823 0.719,3.979 0.313,0.156 10 false ALT 1.229,4.99 1.75,5.24 0.521,0.25 10 false AI-PMP 5.958,7.583 6.292,7.729 0.333,0.146 10 false C45 5.948,7.385 6.302,7.542 0.354,0.156 10 false 60*4 6.49,8.208 6.854,8.406 0.365,0.198 10 false ECM 0.531,6.604 1.031,6.781 0.5,0.177 10 false Battery 4.021,7.198 5.76,7.344 1.74,0.146 10 false Emission Control Valve Set 4.802,4.333 4.927,4.531 0.125,0.198 10 false 5 5.156,4.76 5.281,4.948 0.125,0.188 10 false 3 5.156,5.396 5.271,5.573 0.115,0.177 10 false 2 5.156,6.063 5.302,6.229 0.146,0.167 10 false 4 4.698,6.667 4.823,6.865 0.125,0.198 10 false 1 1.833,4.479 1.969,4.677 0.135,0.198 10 false 2 1.833,5.344 1.958,5.542 0.125,0.198 10 false 1 2.583,4.479 2.708,4.677 0.125,0.198 10 false 5 2.583,5.344 2.708,5.531 0.125,0.188 10 false 3 2.438,6.354 2.563,6.552 0.125,0.198 10 false 1 3.063,6.354 3.177,6.531 0.115,0.177 10 false 2 3.073,7.125 3.219,7.292 0.146,0.167 10 false 4 2.438,7.115 2.563,7.302 0.125,0.188 10 false 3 0.177,0.094 1.135,0.365 0.958,0.271 10 false for Bank 1: 6.323,7.583 6.813,7.76 0.49,0.177 10 false HAI1*1 4.833,4.875 5.115,5.052 0.281,0.177 10 false AIP 3.083,5.344 3.438,5.5 0.354,0.156 10 false C136 3.052,5.51 3.771,5.719 0.719,0.208 10 false Air Pump*2 4,5.927 4.125,6.125 0.125,0.198 10 false 1 4,5.073 4.115,5.25 0.115,0.177 10 false 2 1.052,6.135 1.292,6.406 0.24,0.271 10 false *1 2.344,5.906 2.583,6.177 0.24,0.271 10 false *1 2.115,4.219 2.354,4.49 0.24,0.271 10 false *1 2.823,5.906 3.063,6.177 0.24,0.271 10 false *1 3.438,4.313 3.677,4.583 0.24,0.271 10 false *2 0.5,8.083 2.208,8.292 1.708,0.208 10 false *1: w/ Air Pump Heater 3.208,8.083 5.479,8.292 2.271,0.208 10 false *5: w/ Heated Windshield Defroster 0.5,8.427 2.208,8.635 1.708,0.208 10 false *2: w/o Air Pump Heater 5.646,1.01 6.042,1.156 0.396,0.146 10 false A52 5.635,4.865 5.958,5.083 0.323,0.219 10 false A52 5.656,1.625 6.083,1.771 0.427,0.146 10 false C46 5.646,2.906 6.083,3.052 0.438,0.146 10 false C46 5.635,6.167 5.969,6.313 0.333,0.146 10 false C46 5.646,2.281 6.073,2.427 0.427,0.146 10 false C46 5.625,5.51 5.958,5.656 0.333,0.146 10 false C46 5.625,0.823 5.969,0.99 0.344,0.167 10 false 34*3 5.625,1.448 5.969,1.604 0.344,0.156 10 false 30*3 5.625,2.094 5.969,2.25 0.344,0.156 10 false 28*3 5.625,2.667 5.969,2.823 0.344,0.156 10 false 54*3 5.625,5.333 5.969,5.49 0.344,0.156 10 false 67*3 5.625,4.677 5.99,4.844 0.365,0.167 10 false 54*3 5.625,5.979 5.948,6.146 0.323,0.167 10 false 98*3 5.615,7.594 5.948,7.74 0.333,0.146 10 false C46 5.615,7.406 5.969,7.563 0.354,0.156 10 false 60*3 2.24,8.094 3.01,8.302 0.771,0.208 10 false *3: for RHD 2.24,8.458 3.01,8.667 0.771,0.208 10 false *4: for LHD 4.917,1.573 5.083,1.75 0.167,0.177 10 false DI 4.823,2.208 5.104,2.385 0.281,0.177 10 false SIV 4.823,2.896 5.104,3.073 0.281,0.177 10 false SIP 5.021,3.708 5.906,4.042 0.885,0.333 10 false Air Injection 3.104,6.563 3.229,6.76 0.125,0.198 10 false B 3.104,6.969 3.229,7.167 0.125,0.198 10 false E 2.573,6.583 2.969,6.771 0.396,0.188 10 false APH+ 2.573,6.99 2.99,7.177 0.417,0.188 10 false APHG 4.042,5.281 4.167,5.479 0.125,0.198 10 false B 4.042,5.729 4.167,5.927 0.125,0.198 10 false E 3.083,1.49 3.24,1.635 0.156,0.146 10 false 1 3.469,1.49 3.625,1.635 0.156,0.146 10 false 2 1.073,3.823 1.875,4.01 0.802,0.188 10 false SUB-R/B*5

CAUTION / NOTICE / HINT

HINT:
·

By using the GTS to perform the Secondary Air Injection Check operation in the System Check, the air-fuel ratio and the pressure in the secondary air injection system passage can be checked while the secondary air injection system is operating. This helps technicians to troubleshoot the system when it malfunctions.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.INSPECT AIR SWITCHING VALVE ASSEMBLY
a.

Inspect the air switching valve assembly for bank 1 (See page Engine / Hybrid System>1UR-FE (EMISSION CONTROL)>AIR SWITCHING VALVE(for Bank 1)>INSPECTION).



OK

2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND)

NG

2.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND)
a.

Disconnect the air switching valve connector.


b.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C137-1 (GND) - Body ground Always Below 1 Ω




OK

3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER)
a.

Disconnect the air switching valve connector.


b.

Disconnect the air injection control driver connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
Tester Connection Condition Specified Condition
C137-5 (+B) - C61-6 (VV) Always Below 1 Ω
C137-5 (+B) or C61-6 (VV) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR