Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › from 2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0013  Camshaft Position "B" Actuator Circuit / Open (Bank 1)  P0023  Camshaft Position "B" Actuator Circuit / Open (Bank 2)  


DESCRIPTION

·

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

·

The VVT (Variable Valve Timing) system adjusts the intake and exhaust valve timing to improve driveability. The engine oil pressure turns the camshaft timing gear to adjust the valve timing. The camshaft timing oil control valve is a solenoid valve and switches the engine oil line. The valve moves when the ECM applies 12 volts to the solenoid. The ECM changes the energizing time of the solenoid (duty cycle) in accordance with the camshaft position, crankshaft position, throttle position, etc.


A192077E18
4.483,0.815 5.290,0.978 0.807,0.163 10 VVT Sensor 4.483,1.325 6.216,1.485 1.733,0.161 10 Crankshaft Position Sensor 0.068,0.015 1.618,0.267 1.550,0.253 10 VVT System: 2.333,1.96 3.609,2.134 1.277,0.174 10 Target Valve Timing 2.333,1.287 3.609,1.462 1.277,0.174 10 Actual Valve Timing 2.683,2.695 3.397,2.870 0.714,0.174 10 Correction 2.822,3.204 3.223,3.378 0.402,0.174 10 ECM 1.599,3.747 3.802,3.922 2.203,0.174 10 Camshaft Timing Oil Control Valve 0.166,2.69 0.860,2.864 0.695,0.174 10 Duty Cycle 4.483,1.827 5.808,1.981 1.325,0.154 10 Mass Air Flow Meter 4.483,2.854 6.827,3.042 2.344,0.188 10 Engine Coolant Temperature Sensor 4.483,2.344 6.031,2.511 1.547,0.167 10 Throttle Position Sensor 4.483,3.353 5.938,3.506 1.455,0.154 10 Vehicle Speed Sensor 0.313,4.269 1.682,4.474 1.369,0.205 10 Engine Oil Pressure 3.659,4.217 5.653,4.400 1.994,0.184 10 Camshaft Timing Exhaust Gear 3.883,4.917 5.090,5.101 1.207,0.184 10 Exhaust Camshaft 2.562,4.571 2.842,4.275 2.842,4.275 3.607,4.275 false 3.177,4.781 3.32,5.008 3.32,5.008 3.852,5.008 false

DTC No. DTC Detection Condition Trouble Area
P0013 Open or short in the camshaft timing oil control valve for exhaust side (for Bank 1) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve for exhaust side (for Bank 1) circuit

·

Camshaft timing oil control valve assembly for exhaust side (for Bank 1)

·

ECM


P0023 Open or short in the camshaft timing oil control valve for exhaust side (for Bank 2) circuit (1 trip detection logic).
·

Open or short in camshaft timing oil control valve for exhaust side (for Bank 2) circuit

·

Camshaft timing oil control valve assembly for exhaust side (for Bank 2)

·

ECM



MONITOR DESCRIPTION

These DTCs are designed to detect opens or shorts in the camshaft timing oil control valve circuit. If the camshaft timing oil control valve duty cycle is excessively high or low while the engine is running, the ECM will illuminate the MIL and store the DTC.

The monitor for this DTC runs 5 seconds after the engine switch is turned on (IG).

CONFIRMATION DRIVING PATTERN

1.

Turn the engine switch on (IG) and wait for 5 seconds or more.


WIRING DIAGRAM

U163112E01
5.855,4.132 6.206,4.315 0.350,0.184 10 ECM 5.408,0.512 5.842,0.668 0.434,0.156 10 OE1+ 5.408,1.241 5.775,1.397 0.368,0.156 10 OE1- 5.408,2.488 5.842,2.644 0.434,0.156 10 OE2+ 5.408,3.216 5.842,3.372 0.434,0.156 10 OE2- 0.089,1.638 4.772,1.861 4.684,0.223 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Side of Bank 1) 0.089,3.623 4.695,3.815 4.606,0.192 10 Camshaft Timing Oil Control Valve Assembly (for Exhaust Side of Bank 2) 0.089,1.456 0.544,1.621 0.456,0.165 10 C125 0.089,3.455 0.733,3.620 0.645,0.165 10 C126 1.453,0.497 1.579,0.688 0.126,0.191 10 1 1.46,1.236 1.579,1.409 0.119,0.173 10 2 1.453,2.451 1.579,2.641 0.126,0.191 10 1 1.46,3.189 1.579,3.362 0.119,0.173 10 2 5.059,3.144 5.362,3.300 0.303,0.156 10 49*2 5.059,2.407 5.372,2.563 0.313,0.156 10 50*2 5.059,1.174 5.386,1.330 0.327,0.156 10 55*2 5.059,0.436 5.414,0.592 0.355,0.156 10 56*2 5.073,0.599 5.371,0.742 0.298,0.142 10 C45 5.073,1.338 5.371,1.480 0.298,0.142 10 C45 5.073,2.571 5.371,2.713 0.298,0.142 10 C45 5.073,3.314 5.371,3.456 0.298,0.142 10 C45 4.737,3.144 5.040,3.300 0.303,0.156 10 49*1 4.737,2.407 5.050,2.563 0.313,0.156 10 50*1 4.737,1.174 5.064,1.330 0.327,0.156 10 55*1 4.737,0.436 5.092,0.592 0.355,0.156 10 56*1 4.75,0.599 5.048,0.742 0.298,0.142 10 C46 4.75,1.338 5.048,1.480 0.298,0.142 10 C46 4.75,2.571 5.048,2.713 0.298,0.142 10 C46 4.75,3.314 5.048,3.456 0.298,0.142 10 C46 0.984,4.116 1.758,4.279 0.774,0.163 10 *1: for RHD 0.984,4.368 1.758,4.531 0.774,0.163 10 *2: for LHD

CAUTION / NOTICE / HINT

HINT:
·

If DTC P0013 is output, check the bank 1 VVT system for the exhaust camshaft circuit.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

If DTC P0023 is output, check the bank 2 VVT system for the exhaust camshaft circuit.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.

·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.



PROCEDURE

1.CHECK FOR DTC (DTC P0013 OR P0023)
a.

Connect the GTS to the DLC3.


b.

Clear the DTCs after recording the freeze frame data and DTCs.


c.

Turn the engine switch off.


d.

Start the engine and allow it to idle. Then check for DTCs.


e.

Check that P0013 or P0023 is not output.

OK:

P0013 or P0023 is not output.




OK

NG

2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
2.INSPECT CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY
a.

Inspect the camshaft timing oil control valve assembly (See page Engine / Hybrid System>1UR-FE (ENGINE CONTROL)>CAMSHAFT OIL CONTROL VALVE>INSPECTION).



OK

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)

NG

REPLACE CAMSHAFT TIMING OIL CONTROL VALVE ASSEMBLY

3.CHECK HARNESS AND CONNECTOR (CAMSHAFT TIMING OIL CONTROL VALVE - ECM)
a.

Disconnect the camshaft timing oil control valve connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C125-1 - C46-56 (OE1+) Always Below 1 Ω
C125-2 - C46-55 (OE1-) Always Below 1 Ω
C126-1 - C46-50 (OE2+) Always Below 1 Ω
C126-2 - C46-49 (OE2-) Always Below 1 Ω
C125-1 or C46-56 (OE1+) - Body ground Always 10 kΩ or higher
C125-2 or C46-55 (OE1-) - Body ground Always 10 kΩ or higher
C126-1 or C46-50 (OE2+) - Body ground Always 10 kΩ or higher
C126-2 or C46-49 (OE2-) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C125-1 - C45-56 (OE1+) Always Below 1 Ω
C125-2 - C45-55 (OE1-) Always Below 1 Ω
C126-1 - C45-50 (OE2+) Always Below 1 Ω
C126-2 - C45-49 (OE2-) Always Below 1 Ω
C125-1 or C45-56 (OE1+) - Body ground Always 10 kΩ or higher
C125-2 or C45-55 (OE1-) - Body ground Always 10 kΩ or higher
C126-1 or C45-50 (OE2+) - Body ground Always 10 kΩ or higher
C126-2 or C45-49 (OE2-) - Body ground Always 10 kΩ or higher




OK

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR