Home › Engine / Hybrid System › 1UR-FE (ENGINE CONTROL) › SFI SYSTEM › 2014.08–2015.08
RM2660E _51 Engine / Hybrid System _052772 1UR-FE ENGINE CONTROL _0254983 SFI SYSTEM C

1UR-FE ENGINE CONTROL  SFI SYSTEM  P0365  Camshaft Position Sensor "B" Circuit (Bank 1)  P0367  Camshaft Position Sensor "B" Circuit Low Input (Bank 1)  P0368  Camshaft Position Sensor "B" Circuit High Input (Bank 1)  P0390  Camshaft Position Sensor "B" Circuit (Bank 2)  P0392  Camshaft Position Sensor "B" Circuit Low Input (Bank 2)  P0393  Camshaft Position Sensor "B" Circuit High Input (Bank 2)  


DESCRIPTION

The exhaust camshaft VVT sensor (EV1 and EV2 signals) consists of a magnet and MRE (Magnetoresistive Element).

The exhaust camshaft has 3 teeth on its outer circumference. When the exhaust camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the exhaust camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends the data to the ECM.

DTC No. DTC Detection Condition Trouble Area
P0365
P0390
No VVT sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic).
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Timing chain jumped tooth

·

ECM


P0367
P0392
Output voltage of VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Timing chain jumped tooth

·

ECM


P0368
P0393
Output voltage of VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic).
·

Open or short in VVT sensor for exhaust camshaft circuit

·

VVT sensor for exhaust camshaft

·

Exhaust camshaft

·

Timing chain jumped tooth

·

ECM



A217927E02
0.21,1.18 0.440,1.345 0.230,0.165 10 NE 0.137,1.731 0.441,1.882 0.304,0.151 10 EV1 0.141,2.093 0.440,2.238 0.299,0.145 10 EV2 2.847,1.272 3.184,1.421 0.336,0.149 10 GND 2.847,2.197 3.184,2.346 0.336,0.149 10 GND 2.847,1.824 3.184,1.973 0.336,0.149 10 GND 1.07,2.506 1.991,2.648 0.921,0.141 10 20 msec./DIV. 2.691,0.783 3.254,0.939 0.563,0.156 10 5 V/DIV. 0.061,0.068 2.369,0.246 2.308,0.178 10 EV1, EV2 and NE Signal Waveforms

Reference: Inspection using an oscilloscope

Standard:
for RHD
Tester Connection Tool Setting Condition Specified Condition
C46-110 (NE+) - C46-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C46-69 (EV1+) - C46-68 (EV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C46-64 (EV2+) - C46-65 (EV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown

for LHD
Tester Connection Tool Setting Condition Specified Condition
C45-110 (NE+) - C45-111 (NE-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C45-69 (EV1+) - C45-68 (EV1-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown
C45-64 (EV2+) - C45-65 (EV2-) 5 V/DIV.
20 msec./DIV.
Cranking or idling The correct waveform is as shown


HINT:

EV1 and EV2 are the VVT sensor signals, and NE is the crankshaft position sensor signal.



MONITOR DESCRIPTION

If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.

Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.

CONFIRMATION DRIVING PATTERN

1.

Start the engine and run it at idle for 10 seconds or more.


WIRING DIAGRAM

A276694E02
5.165,0.815 5.580,0.980 0.415,0.165 10 VCV2 5.165,1.357 5.580,1.522 0.415,0.165 10 EV1+ 5.161,1.885 5.576,2.050 0.415,0.165 10 EV1- 5.161,3.795 5.576,3.960 0.415,0.165 10 EV2+ 5.161,4.322 5.576,4.488 0.415,0.165 10 EV2- 0.925,2.544 3.562,2.737 2.637,0.193 10 VVT Sensor (for Exhaust Side of Bank 1) 0.925,4.982 3.581,5.165 2.656,0.184 10 VVT Sensor (for Exhaust Side of Bank 2) 0.906,2.348 1.293,2.522 0.387,0.174 10 C121 0.925,4.772 1.312,4.946 0.387,0.174 10 C122 5.221,5.122 6.581,5.315 1.360,0.193 10 C46*1, C45*2 5.221,5.29 5.590,5.483 0.369,0.193 10 ECM 4.894,0.807 5.073,0.986 0.179,0.179 10 66 4.894,1.339 5.078,1.513 0.184,0.174 10 69 4.894,1.862 5.094,2.020 0.200,0.158 10 68 4.894,3.768 5.078,3.942 0.184,0.174 10 64 4.894,4.291 5.094,4.449 0.200,0.158 10 65 2.634,1.311 2.767,1.518 0.133,0.207 10 1 2.634,0.769 2.767,0.976 0.133,0.207 10 3 2.634,1.848 2.767,2.055 0.133,0.207 10 2 2.629,3.744 2.762,3.951 0.133,0.207 10 1 2.629,3.202 2.762,3.409 0.133,0.207 10 3 2.629,4.281 2.762,4.488 0.133,0.207 10 2 2.251,0.797 2.578,0.962 0.327,0.165 10 VC2 2.26,1.315 2.675,1.480 0.415,0.165 10 EX+ 2.26,1.875 2.675,2.040 0.415,0.165 10 EX- 2.256,3.221 2.588,3.386 0.332,0.165 10 VC2 2.26,3.753 2.675,3.918 0.415,0.165 10 EX+ 2.26,4.313 2.675,4.478 0.415,0.165 10 EX- 3.818,4.835 4.578,5.030 0.760,0.195 10 *1: for RHD 3.818,5.096 4.578,5.291 0.760,0.195 10 *2: for LHD

CAUTION / NOTICE / HINT

HINT:
·

Read freeze frame data using the GTS. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.

·

Bank 1 refers to the bank that includes the No. 1 cylinder*.

*: The No. 1 cylinder is the cylinder which is farthest from the transmission.

·

Bank 2 refers to the bank that does not include the No. 1 cylinder.



PROCEDURE

1.CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE)
a.
U163268E01
0.084,0.069 0.316,0.274 0.231,0.205 10 *a 0.19,1.56 0.546,1.761 0.357,0.201 10 C121 0.183,1.943 0.549,2.144 0.366,0.201 10 C122 0.647,1.573 0.814,1.774 0.167,0.201 10 *b 0.647,1.912 0.814,2.113 0.167,0.201 10 *c 2.788,2.499 3.119,2.650 0.332,0.151 10 VC2 1.986,2.216 2.742,2.555 false

Disconnect the VVT sensor connector.


b.

Measure the voltage according to the value(s) in the table below.

Standard Voltage:
Tester Connection Switch Condition Specified Condition
3 (VC2) - Body ground Engine switch on (IG) 4.5 to 5.0 V


Text in Illustration
*a Front view of wire harness connector
(to VVT Sensor)
*b Bank 1
*c Bank 2



OK

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

2.CHECK HARNESS AND CONNECTOR (VVT SENSOR - ECM)
a.

Disconnect the VVT sensor connector.


b.

Disconnect the ECM connector.


c.

Measure the resistance according to the value(s) in the table below.

Standard Resistance:
for RHD
Tester Connection Condition Specified Condition
C121-1 (EX+) - C46-69 (EV1+) Always Below 1 Ω
C121-2 (EX-) - C46-68 (EV1-) Always Below 1 Ω
C122-1 (EX+) - C46-64 (EV2+) Always Below 1 Ω
C122-2 (EX-) - C46-65 (EV2-) Always Below 1 Ω
C121-1 (EX+) or C46-69 (EV1+) - Body ground Always 10 kΩ or higher
C121-2 (EX-) or C46-68 (EV1-) - Body ground Always 10 kΩ or higher
C122-1 (EX+) or C46-64 (EV2+) - Body ground Always 10 kΩ or higher
C122-2 (EX-) or C46-65 (EV2-) - Body ground Always 10 kΩ or higher

for LHD
Tester Connection Condition Specified Condition
C121-1 (EX+) - C45-69 (EV1+) Always Below 1 Ω
C121-2 (EX-) - C45-68 (EV1-) Always Below 1 Ω
C122-1 (EX+) - C45-64 (EV2+) Always Below 1 Ω
C122-2 (EX-) - C45-65 (EV2-) Always Below 1 Ω
C121-1 (EX+) or C45-69 (EV1+) - Body ground Always 10 kΩ or higher
C121-2 (EX-) or C45-68 (EV1-) - Body ground Always 10 kΩ or higher
C122-1 (EX+) or C45-64 (EV2+) - Body ground Always 10 kΩ or higher
C122-2 (EX-) or C45-65 (EV2-) - Body ground Always 10 kΩ or higher




OK

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)

NG

REPAIR OR REPLACE HARNESS OR CONNECTOR

3.CHECK SENSOR INSTALLATION (VVT SENSOR FOR EXHAUST CAMSHAFT)
a.
B449531E02
1.427,1.552 2.219,1.781 0.792,0.229 10 false Clearance 2.458,1.844 3.156,2.104 0.698,0.26 10 false Abnormal 0.375,1.667 0.99,1.927 0.615,0.26 10 false Normal

Check the VVT sensor installation.

OK:

Sensor is installed correctly.




OK

4.INSPECT EXHAUST CAMSHAFT

NG

4.INSPECT EXHAUST CAMSHAFT
a.

Check the teeth of the camshaft.

OK:

Teeth do not have any cracks or deformation.




OK

5.REPLACE VVT SENSOR

NG

5.REPLACE VVT SENSOR

NEXT

6.CHECK WHETHER DTC OUTPUT RECURS
6.CHECK WHETHER DTC OUTPUT RECURS
a.

Connect the GTS to the DLC3.


b.

Turn the engine switch on (IG).


c.

Turn the GTS on.



e.

Start the engine and idle it for 10 seconds or more.


f.

Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.


g.

Read DTCs.

Result
Display (DTC Output) Proceed to
No DTC is output A
P0365, P0367, P0368, P0390, P0392 or P0393 is output B

HINT:

If the engine does not start, replace the ECM.




A

END

B