11302
1.REMOVE TIMING CHAIN COVER SUB-ASSEMBLY
2.SET NO. 1 CYLINDER TO TDC/COMPRESSION
13540
3.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY LH
Move the stopper plate upward to release the lock and push the plunger deep into the No. 1 chain tensioner.
| *1 | Plunger |
| *2 | Stopper Plate |
Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.
| *1 | Plunger |
| *2 | Stopper Plate |
| *3 | Hexagon Wrench |
Remove the 2 bolts, No. 1 chain tensioner LH and gasket.
13559
4.REMOVE CHAIN TENSIONER SLIPPER LH
13561
5.REMOVE NO. 1 CHAIN VIBRATION DAMPER LH
Remove the 2 bolts and No. 1 chain vibration damper LH.
13506
6.REMOVE NO. 1 CHAIN SUB-ASSEMBLY LH
While pushing down the No. 3 chain tensioner, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.
| *1 | Pin |
| *2 | Plunger |
| *3 | No. 3 Chain Tensioner |
| *a | Push |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
| *a | Hold |
|
Turn |
Be careful not to damage the cylinder head with the wrench.
Do not disassemble the camshaft timing gear.
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
| *a | Hold |
|
Turn |
Be careful not to damage the cylinder head with the wrench.
Do not disassemble the camshaft timing exhaust gear.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket LH.
Remove the No. 1 and No. 2 chains from the gears.
13560A
7.REMOVE NO. 3 CHAIN TENSIONER ASSEMBLY
Remove the 2 bolts and No. 3 chain tensioner.
13540
8.REMOVE NO. 1 CHAIN TENSIONER ASSEMBLY RH
Move the stopper plate upward to release the lock and push the plunger deep into the No. 1 chain tensioner.
| *1 | Plunger |
| *2 | Stopper Plate |
Move the stopper plate downward to set the lock and insert a hexagon wrench into the stopper plate hole.
| *1 | Plunger |
| *2 | Stopper Plate |
| *3 | Hexagon Wrench |
Remove the 2 bolts and No. 1 chain tensioner RH.
13559
9.REMOVE CHAIN TENSIONER SLIPPER RH
13561
10.REMOVE NO. 1 CHAIN VIBRATION DAMPER RH
Remove the 2 bolts and No. 1 chain vibration damper RH.
13506
11.REMOVE NO. 1 CHAIN SUB-ASSEMBLY RH
While raising up the No. 2 chain tensioner, insert a pin with a diameter of 1.0 mm (0.0394 in.) into the hole to fix the tensioner in place.
| *1 | Pin |
| *2 | Plunger |
| *3 | No. 2 Chain Tensioner |
| *a | Push |
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
| *a | Hold |
|
Turn |
Be careful not to damage the cylinder head with the wrench.
Do not disassemble the camshaft timing gear.
Hold the hexagonal portion of the camshaft with a wrench and loosen the bolt.
| *a | Hold |
|
Turn |
Be careful not to damage the cylinder head with the wrench.
Do not disassemble the camshaft timing exhaust gear.
Remove the 2 bolts. Then with the No. 1 and No. 2 chains still connected to the gears, remove the camshaft timing gear, camshaft timing exhaust gear and crankshaft timing sprocket RH.
Remove the No. 1 and No. 2 chains from the gears.
13550
12.REMOVE NO. 2 CHAIN TENSIONER ASSEMBLY
Remove the 2 bolts and No. 2 chain tensioner.
13.REMOVE CAMSHAFT BEARING CAP LH
Make sure that the knock pins of the camshafts are positioned as shown in the illustration.
| *A | for Intake Side |
| *B | for Exhaust Side |
| *1 | Knock Pin |
Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 6 camshaft bearing caps.
Arrange the removed parts in the correct order.
13053
14.REMOVE NO. 3 CAMSHAFT SUB-ASSEMBLY
Remove the No. 3 camshaft from the camshaft housing LH.
13054
15.REMOVE NO. 4 CAMSHAFT SUB-ASSEMBLY
Remove the No. 4 camshaft from the camshaft housing LH.
11104A
16.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY LH
Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
| *1 | Protective Tape |
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.
Tape the screwdriver tip before use.
17.REMOVE CAMSHAFT BEARING CAP RH
Make sure that the knock pins of the camshafts are positioned as shown in the illustration.
| *A | for Exhaust Side |
| *B | for Intake Side |
| *1 | Knock Pin |
Uniformly loosen and remove the 10 bearing cap bolts in the sequence shown in the illustration.
Uniformly loosen and remove the 18 bearing cap bolts in the sequence shown in the illustration.
Uniformly loosen the bolts while keeping the camshaft level.
Remove the 6 camshaft bearing caps.
Arrange the removed parts in the correct order.
13511
18.REMOVE NO. 1 CAMSHAFT SUB-ASSEMBLY
Remove the No. 1 camshaft from the camshaft housing RH.
13512
19.REMOVE NO. 2 CAMSHAFT SUB-ASSEMBLY
Remove the No. 2 camshaft from the camshaft housing RH.
11103C
20.REMOVE CAMSHAFT HOUSING SUB-ASSEMBLY RH
Remove the camshaft housing by prying between the cylinder head and camshaft housing with a screwdriver.
| *1 | Protective Tape |
Be careful not to damage the contact surfaces of the cylinder head and camshaft housing.
Tape the screwdriver tip before use.
13050
21.INSPECT CAMSHAFT TIMING GEAR ASSEMBLY
13080
22.INSPECT CAMSHAFT TIMING EXHAUST GEAR ASSEMBLY